INFLUENCE OF FRICTION ON SHAPING OF A FLAT BLANK
https://doi.org/10.17073/0368-0797-2018-3-251-253
Abstract
Investigations of the friction influence on the shaping of a flat blank are presented. It is shown that the shaping of a flat blank is determined by kinematic scheme of the metal flow. An intermediate kinematic scheme of the metal flow is proposed. It is proved that as the coefficient of friction increases, the «radial» kinematic scheme of the metal flow smoothly changes to «normal». Evaluation of the friction influence was carried out using computer and physical simulation. For computer simulation the DEFORM program complex was used. Plasticine was chosen as the material for the physical simulation of flat blank shaping. When comparing the results of virtual and laboratory experiments, there is almost complete coincidence.
About the Authors
L. I. Tishchuk
Voronezh branch of the Rostov State Transport University
Russian Federation
Russian Federation
Lecturer
K. N. Solomonov
Voronezh branch of the Rostov State Transport University
Russian Federation
Dr. Sci. (Eng.), Professor of the Chair “Theoretical and Applied Mechanics”
Russian Federation
Dr. Sci. (Eng.), Professor of the Chair “Theoretical and Applied Mechanics”
References
1. Gorbatyuk S.M., Gerasimova A.A., Belkina N.N. Applying thermal coatings to narrow walls of the continuous-casting molds. Materials Science Forum. 2016, vol. 870, pp. 564–567.
2. Gorbatyuk S.M., Morozova I.G., Naumova M.G. Color mark formation on a metal surface by a highly concentrated energy source. Metallurgist. 2016, no. 60, pp. 646–650.
3. Mazur I.P., Borisov S.S., Kavalek A. Investigation of hardening of hard-to-deformable steel of HSLA type during cold rolling. Proizvodstvo prokata. 2012, no. 7, pp. 8–13. (In Russ.).
4. Sobbe C. Beiträge zur Technologie des Schmiedepressens. Werkstattstechnik. 1908, no. 9, S. 457–471.
5. Tarnovskii I.Ya., Pozdeev A.A., Ganago O.A. Deformatsii i usiliya pri obrabotke metallov davleniem [Deformations and forces at metal forming]. Moscow: Mashgiz, 1959, 304 p. (In Russ.).
6. Golovin A.F. Prokatka: v 2-kh t. [Rolling: in 2 vols.]. Moscow: Metallurgizdat, 1933. (In Russ.).
7. Solomonov K.N., Kostarev I.V., Abashkin V.P. Modelirovanie protsessov ob”emnoi shtampovki i kovki ploskikh zagotovok [Simulation of processes of bulk forging and forging of flat blanks]. Moscow: ID MISiS, 2008, 128 p. (In Russ.).
8. Solomonov K. Development of software for simulation of forming forgings. Procedia Engineering. 2014, no. 81, pp. 437–443.
9. Storozhev M.V., Popov E.A. Teoriya obrabotki metallov davleniem [Theory of metal forming]. Moscow: Mashinostroenie, 1971, 424 p. (In Russ.).
10. Gubkin S.I. Plasticheskaya deformatsiya metallov: v 3-kh t. [Plastic deformation of metals: in 3 vols.]. Moscow: Metallurgizdat, 1960. (In Russ.).
Review
For citations:
Tishchuk L.I., Solomonov K.N. INFLUENCE OF FRICTION ON SHAPING OF A FLAT BLANK. Izvestiya. Ferrous Metallurgy. 2018;61(3):251-253. (In Russ.) https://doi.org/10.17073/0368-0797-2018-3-251-253
Views:
508
Email this article 