DETERMINATION OF RESIDUAL STRESSES IN THE CALIBRATED ROD

Calibrated metal is presented as an effective form of blanks for a number of metal technologies. Greater its use in industry prevent residual stresses formed during cold deformation. The aim of this study was to determine the main calibration parameters that influence the formation of residual stresses. The main components of the tensor of residual stresses in a calibrated rod were determined by the method of grinding and boring of one cylinder. The planning methodology of multivariate experiments was used to determine the effect of the main parameters of the calibration process on the residual stress state. For the account of simultaneous effect on the residual stresses of the relative compression, angle of the working cone of the die, calibration speed and lubrication quality the fractional four-factor experiment has been planned and implemented. These experiments have shown that the parameters of the calibration process significantly affect the residual stresses, which vary not only in magnitude but also in sign. Experimental results have shown that the range of angles of the die was from 8 to 24°, the tangential and axial residual stresses increase simultaneously: increase by 2.3 and 1.8 times. With the increase in the length of the gauge zones maximum axial residual tensile stresses are reduced by 52 % and tangential increased by 21 %. The influence of the main parameters of the calibration process on the size and nature of the distribution over the cross section of cylindrical rods of axial, radial and tangential residual stresses was determined. Changing the sign of the residual stress depends on the deformation parameters and occurs at a depth of (0,5  –  0,8)r/R. It was revealed that at the calibration mode that is used in the production the axial and tangential residual tensile stresses are formed in the peripheral layers of rods at cold forming, and in the central layers – the compressive stresses are formed. Radial residual stresses at the surface are zero, and in the rest of the body volume residual stresses are compressive.

calibrated metal, residual stresses, calibration parameters, compression, working cone angle, length of the gauge area

1. Sheftel’N.I. Uluchshenie kachestva i sortamenta prokata [Improvement of the quality and rolled products range]. Moscow: Metallurgiya, 1973, 343 p. (In Russ.).

2. Nedovizii I.N., Zavalishin N.I. Main ways to increase the efficiency of the usage of metals in hardware production. In: Povyshenie effektivnosti ispol’zovaniya metalla v metiznom proizvodstve [Increase the efficiency of the usage of metals in hardware production]. Moscow: Metallurgiya, 1983, pp. 7–16. (In Russ.).

3. Belalov Kh.N., Klekovkin A.A., Klekovkina N.A. etc. Stal’naya provoloka [Steel wire]. Magnitogorsk: ITs MGTU, 2011, 689 p. (In Russ.).

4. Zaides S.A. Ostatochnye napryazheniya i kachestvo kalibrovannogo metalla [Internal stresses and quality of calibrated metal]. Irkutsk: IrGTU, 1992, 200 p. (In Russ.).

5. Zaides S.A. Okhvatyvayushchee poverkhnostnoe plasticheskoe deformirovanie [Cover surface plastic deformation]. Irkutsk: IrGTU, 2001, 309 p. (In Russ.).

6. Sokolov I.A., Ural’skii V.I. Ostatochnye napryazheniya i kachestvo metalloproduktsii [Internal stresses and quality of metal products]. Moscow: Metallurgiya, 1981, 97 p. (In Russ.).

7. Pozdeev A.A., Nyashin Yu.I., Trusov P.V. Ostatochnye napryazheniya. Teoriya i prilozheniya [Internal stresses. Theory and supplement]. Moscow: Nauka, 1982, 111 p. (In Russ.).

8. Vishnyakov Ya.D., Piskarev V.D. Upravlenie ostatochnymi napryazheniyami v metallakh i splavakh [Control of internal stresses in metals and alloys]. Moscow: Metallurgiya, 1989, 253 p. (In Russ.).

9. Skorokhodov A.N., Zudov E.G., Kirichkov A.A, Petrenko Yu.P. Ostatochnye napryazheniya v profilyakh i sposoby ikh snizheniya [Internal stresses in cross-sections and ways of their reduction]. Moscow: Metalurgiya, 1985, 185 p. (In Russ.).

10. Alekseev P.G. Resistance of internal stresses and their influence on durability, hardened with cold hardening. In: Povyshenie ekspluatatsionnykh svoistv detalei poverkhnostnym plasticheskim deformirovaniem [Increase of operational properties of parts by surface plastic deformation]. Moscow: MDNTP, 1971, pp. 76–79. (In Russ.).

11. Ostatochnye napryazheniya [Internal stresses]. Makarevich S.S. ed. Minsk: UP Tekhnoprint, 2003, 316 p. (In Russ.).

12. Tekhnologicheskie ostatochnye napryazheniya [Technological internal stresses]. Podzei A.V. ed. Moscow: Mashinostroenie, 1973, 216 p. (In Russ.).

13. Birger I.A. Ostatochnye napryazheniya [Internal stresses]. Moscow: Mashgiz, 1963, 232 p. (In Russ.).

14. Trykov Yu.P., Pokataev E.P., Shmorgun V.G., Khrapov A.A. Ostatochnye napryazheniya v sloistykh kompozitakh [Internal stresses in layered composites]. Moscow: Metallurgizdat, 2010, 237 p. (In Russ.).

15. Zaides S.A., Klimova L.G. Control of technological internal stresses in low-abrasive trucks with braced deformation. Vestnik IrGTU. 2006, no. 4 (28), pp. 58–61. (In Russ.).

16. Rusakov A.A. Rentgenografiya metallov [Metal X-ray diffraction]. Moscow: Atomizdat, 1977, 237 p. (In Russ.).

17. Tekkaya A.E., Gerhardt I. Residual stresses in cold–formed workpieces. Annals of the CIRP. 1985, vol. 34, no. 1, pp. 225–230.

18. Tszeng T.C., Kobayashi S. Determination of residual stresses in radial forming proceedings. Manufacturing Simulation and Processes the Winter Annual Meeting of the American Society of Mechanical Engineers. 1986, pp. 31–45.

19. Kokovikhin Yu.I., Tuktamyshev I.Sh., Polyakov M.G. Metodicheskoe posobie po matematicheskomu planirovaniyu eksperimentov [Study guide in mathematical planning of experiments]. Magnitogorsk: MGTU, 1973, Part 1-2. 76 p. (In Russ.).

20. Novik F.S. Matematicheskie metody planirovaniya eksperimentov v metallovedenii. Razd. 1: Obshchie predstavleniya o planirovanii eksperimentov. Plany pervogo poryadka [Mathematical methods of planning experiments in metallurgical science. Section 1. General overview of the experiment planning. Plans of the first order]. Moscow: MISiS, 1969, 82 p. (In Russ.).

21. Berin I.Sh., Dnestrovskii N.Z. Volochil’nyi instrument [Drawing tool]. Moscow: Mashinostroenie, 1971, 174 p. (In Russ.).

22. Druzhinina T.Ya., Zaides S.A., Arkulis G.E. etc. Internal stresses in calibrated metal and ways of their control. In: Ostatochnye napryazheniya i metody regulirovaniya. Tr. Vsesoyuz. simpoz. po ostatochnym napryazheniyam [Residual stresses and methods of their regulation. Papers of All-Union. Symp. on Residual Stresses]. Moscow: Institut problem mekhaniki AN SSSR, 1982, pp. 175–180. (In Russ.).