ANALYSIS OF CRANK HINGE – RADICAL BEARING OF CRANK-BEAM MECHANISM OF JAW CRUSHER
https://doi.org/10.17073/0368-0797-2016-12-875-878
Abstract
The analysis of lever mechanisms performance, having internal degrees of freedom conditioned by the presence of clearance in joints, has shown that clearances in the joints were the reason of appearance of additional dynamic forces. In order to eliminate the influence of clearances in joints on the origin of additional dynamic forces it is necessary to find regularities of pulse loading appearance. The analysis of the joint performance of a crank–bearing support with a clearance of crank-androcker mechanism of a cheek crusher was made. Based on the obtained results it was defined at which positions of mechanism links the contact surfaces changeover of a joint crank – bearing support appears. This allows to use rationally the mechanisms for the choice of clearances with resilient elements, which choose the clearance in a junction crank – bearing support during the cycle of work of crank-and-rocker, thus, preventing the appearance of the additional dynamic loadings
About the Authors
A. G. Nikitin
Siberian State Industrial University
Russian Federation
Dr. Sci. (Eng.), Assist. Professor, Head of the Chair «Machinery and Technological Equipment»
Russian Federation
Dr. Sci. (Eng.), Assist. Professor, Head of the Chair «Machinery and Technological Equipment»
A. V. Abramov
Siberian State Industrial University
Russian Federation
Postgraduate of the Chair «Machinery and Technological Equipment»
Russian Federation
Postgraduate of the Chair «Machinery and Technological Equipment»
A. A. Gredina
Siberian State Industrial University
Russian Federation
MA Student of the Chair «Machinery and Technological Equipment»
Russian Federation
MA Student of the Chair «Machinery and Technological Equipment»
V. V. Garyashin
LLC “SpetsSvyazOborudovanie”
Russian Federation
Cand. Sci. (Eng.), Head of Design Department
Russian Federation
Cand. Sci. (Eng.), Head of Design Department
References
1. Tselikov A.I., Polukhin P.I., Grebenik V.M. etc. Mashiny i agregaty metallurgicheskikh zavodov. V 3-kh t. T. 1. Mashiny i agregaty domennykh tsekhov [Machines and devices of metallurgical plants. In 3 vols. Vol. 1. Machines and equipment of blast furnaces]. Tselikov A.I. ed. Moscow: Metallurgiya, 1987, 440 p. (In Russ.).
2. Yudin K.M. Dynamic study of the model of mechanisms with clearances. Mashinovedenie. 1971, no. 2, pp. 58–60. (In Russ.).
3. Vul’fson I.I. Kolebaniya mashin s mekhanizmami tsiklovogo deistviya [Oscillations of machines with mechanisms of cycle action]. Leningrad: Mashinostroenie, 1990, 309 p. (In Russ.).
4. Ivanov A.P. Dinamika sistem s mekhanicheskimi soudareniyami [Dynamics of systems with mechanical collisions]. Moscow: Mezhdunarodnaya programma obrazovaniya, 1997, 336 p. (In Russ.).
5. Sergeev V.I., Yudin K.M. On a model of mechanisms with clearances. Mashinovedenie. 1970, no. 5, pp. 28–32. (In Russ.).
6. Dubovski S., Norris M., Aloni E., Tamir A. Theoretical and experimental study of phenomena in planar mechanical systems with clearances. Konstruirovanie i tekhnologiya mashinostroeniya. 1984, no. 4, pp. 148–156. (In Russ.).
7. Nachaev R.F. Mekhanicheskie protsessy s povtornymi zatukhayushchimi soudareniyami [Mechanical processes with repeated damped collisions]. Moscow: Nauka, 1977, 232 p. (In Russ.).
8. Rodov G.M., Ivanov V.A. On dynamic loads in crank presses. Kuznechno-shtampovochnoe proizvodstvo. 1972, no. 3, pp. 28–31. (In Russ.).
9. Rusakov I.G., Kharkevich A.A. Forced vibration of a system beating against the limiter. Zhurnal tekhnicheskoi fi ziki. 1942, vol. 12, no. 11-12, pp. 715–721. (In Russ.).
10. Miropol’skii Yu.A., Nikitin A.G. Influence of clearances in kinematic pairs on reliability of crank forging presses. Kuznechno-shtampovochnoe proizvodstvo. 1999, no. 9, pp. 38–45. (In Russ.).
11. Nikitin A.G., Boiko D.Yu., Vekesser A.Yu. Mathematical operational model of the joint crank – bearing crank-rocker mechanism of a jaw crusher. Izvestiya VUZov. Chernaya metallurgiya = Izvestiya. Ferrous Metallurgy. 2007, no. 10, pp. 66–67. (In Russ.).
12. Lanskoi E.N., Tserlyuk M.D. Choice of rational schemes of dynamic balancing of forging machines. Kuznechno-pressovoe proizvodstvo. 1987, no. 2, pp. 22–26. (In Russ.).
13. Klushantsev B.V., Parnenko Yu.V. To analysis of kinematics of jaw crushers with a complex movement of the jaws. In: Sb. trudov VNIIStroidormasha. Povyshenie nadezhnosti i proizvoditel’nosti drobil’no-obogatitel’nogo oborudovaniya [Proc. of VNIIStroydormash. Increased reliability and performance of crushing and processing equipment]. Vol. 99. Moscow: VNIIStroidormash, 1984, pp. 3–7. (In Russ.).
14. Semenov E.I., Nistratov A.F., Mal’tsev V.K. Krivoshipnyi press [Crank press]. Certifi cate of authorship USSR no. 712266. Byulleten’ izobretenii. 1980, no. 4. (In Russ.).
15. Nikitin A.G., Boiko D.Yu., Vekesser A.Yu. Shchekovaya drobilka [Jaw crusher]. Patent RF no. 2318599. Byulleten’ izobretenii. 2008, no. 7. (In Russ.).
Review
For citations:
Nikitin A.G., Abramov A.V., Gredina A.A., Garyashin V.V. ANALYSIS OF CRANK HINGE – RADICAL BEARING OF CRANK-BEAM MECHANISM OF JAW CRUSHER. Izvestiya. Ferrous Metallurgy. 2016;59(12):875-878. (In Russ.) https://doi.org/10.17073/0368-0797-2016-12-875-878
Views:
625
Email this article 