ANALYSIS OF THE CAUSES OF VERTICAL BENDING OF THE STRIP FRONT END AT HOT ROLLING ON THE BASIS OF MATHEMATICAL MODELING
https://doi.org/10.17073/0368-0797-2016-3-204-208
Abstract
The analysis of the causes of the defect “strip ends bending” was made in conditions of hot rolling at the plate mill 5000. The infl uence of kinematic, thermal and geometrical factors on the occurrence of the defect “strip ends bending” was investigated. The infl uence of the misalignment velocity of work rolls to the bending of front end of a rough billet was studied in details. Therefore 1214 tons of rolls (65 slabs) were examined. The infl uence of rolling process parameters and misalignment velocity of the work rolls to the shape of the strip front end for each pass was analyzed. The modes of asymmetric rolling of alloyed pipe steels at the plate mill 5000 have been developed and simulated in DEFORM environment software package. The authors have proposed concrete recommendations. The production tests of developed asymmetric rolling modes were performed with their analysis and correction. This method can be applied to any type of rolling velocity to adjust the upper and lower rollers independently.
About the Authors
D. N. Chikishev
Magnitogorsk State Technical University named after G.I. Nosov
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Assist. Professor of the Chair “Metal Forming”,
Magnitogorsk
E. B. Pozhidaeva
Magnitogorsk State Technical University named after G.I. Nosov
Russian Federation
Russian Federation
Postgraduate,
Magnitogorsk
References
1. Pesin A.M., Salganik V.M., Drigun E.M., Chikishev D.N. Ustroistvo dlya asimmetrichnoi prokatki tolstolistovogo metalla [Device for the asymmetric rolling of metal plate]. Patent RF no. 2254943, MPK7 V 21V 1/22. Byulleten’ izobretenii. 2005, no. 18. (In Russ.).
2. Shebanits E.N., Klimanchuk V.V., Khlestov V.M., Murashkin A.A., Rubets A.S. Improvement of temperature mode of steel strips controlled rolling in order to stabilize its microstructure and mechanical properties. Metall i lit’e Ukrainy. 2007, no. 1–2, pp. 50–54. (In Russ.).
3. Morozov Yu.D., Naumenko A.A., Lyasotskii I.V. Eff ect of rolling heating and deformation and accelerated cooling regimes on mechanical property formation for rolled steel sheet of strength class Kh80. Metallurgist. 2011, vol. 54, no. 9–10, pp. 686–695.
4. Lorents U., Khertsig K., Blek V., Evartts T. etc. Eff ect of deformation in two-phase α + γ fi eld on the material properties and the technology of producing of thin hot-rolled strip. Chernye metally. 2003, no. 4, pp. 42–49. (In Russ.).
5. Efron L.I., Il’inskii V.I., Golovanov A.V., Morozov Yu.D. Production of cold-resistant tube steels by controlled high-temperature rolling. Steel in Translation. 2003, vol. 33, no. 6, pp. 60–65.
6. Kruglova A.A., Orlov V.V., Khlusova E.I. Eff ect of hot plastic deformation in the austenite interval on structure formation in lowalloyed low-carbon steel. Metal Science and Heat Treatment. 2007, vol. 49, no. 11–12, pp. 556–560.
7. Efron L.I., Morozov Yu.D., Goli-Oglu E.A. Eff ect of controlled rolling regimes on the structure and properties of microalloyed steels for large diameter pipes. Metallurgist. 2011, vol. 55, no. 1–2, pp. 46–53.
8. Romanov P.V., Radchenko V.P. Prevrashchenie austenita pri nepreryvnom okhlazhdenii stali: Atlas termokineticheskikh diagramm [Transformation of austenite under continuous cooling of steel: Atlas of thermo-kinetic diagrams]. Part 1. Novosibirsk: Izd-vo Sib. Otd. AN SSSR, 1960. 51 p. (In Russ.).
9. Popov V.V. Modelirovanie prevrashcheniya karbonitridov pri termicheskoi obrabotke stalei [Modeling of carbonitrides transformation during heat treatment of steels]. Ekaterinburg: UrO-RAN. 2003. 279 p. (In Russ.).
10. Ryzhkov M.A., Popov A.A. Methodological aspects of plotting of thermokinetic diagrams of transformation of supercooled austenite in low-alloy steels. Metal Science and Heat Treatment. 2011, vol. 52, no. 11–12, pp. 612–616.
11. Ouchi C, Okita T. Austenitic Grain Refi nement through Static Recrystallization Immediately after Hot Rolling, Transactions ISIJ. Vol. 24. 1984, pp. 726–733.
12. Kozasu I., Ouchi C., Sampei T., Okita T. Hot rolling as a hightemperature thermo-mechanical process. Micro Alloying 75. 1975. Session 1, pp. 100–115.
13. Ouchi C., Sampei T., Kozasu I. The Eff ect of Hot Rolling Condition and Chemical Composition on the Onset Temperature of γ→α transformation after Hot Rolling. Transactions ISIJ. Vol. 22. 1982, pp. 214–222.
14. Kotsar’ S.L., Belyanskii A.D., Mukhin Yu.A. Tekhnologiya listoprokatnogo proizvodstva [Rolling production technology]. Moscow: Metallurgiya, 1997. 272 p. (In Russ.).
15. Chikishev D.N., Pozhidaeva E.B. Mathematical modeling of changes in the strength characteristics of micro-alloyed steels at thermal deformation processing. Izvestiya Samarskogo nauchnogo tsentra Rossiiskoi akademii nauk. 2014, vol. 16, no. 4-3, pp. 664–668. (In Russ.).
16. ASTMA 1033-04. Standart practice for quantative measurement and reporting of hypoeutectoid carbon and low alloy steel phase transformation. ASTM, 2004. 14 p.
Review
For citations:
Chikishev D.N., Pozhidaeva E.B. ANALYSIS OF THE CAUSES OF VERTICAL BENDING OF THE STRIP FRONT END AT HOT ROLLING ON THE BASIS OF MATHEMATICAL MODELING. Izvestiya. Ferrous Metallurgy. 2016;59(3):204-208. (In Russ.) https://doi.org/10.17073/0368-0797-2016-3-204-208
Views:
793
Email this article 