DEVELOPMENT OF CALCULATING METHOD OF THE DEFORMATION PARAMETERS DURING ROLLING OUT IN A THREE-ROLL MILL LINERS OF SCREW ROLLING
https://doi.org/10.17073/0368-0797-2016-3-167-172
Abstract
The main features of the process of screw rolling of steel pipes by a three-roll mill of screw rolling are considered. Taking into account the variety in distribution of specifi c forces at the deformation zone, the calculation method for the deformation parameters of rolling process of pipe liner in the deformation at the mandrel length was deve loped. The design procedure of partial reductions and contact of the metal surface area with the roll in zones of compression in diameter (reduction) and compression of the liner wall, which takes into account the tangential outfl ow of the metal in the gaps between the rollers, are characteristic for rolling processes of thin-walled pipes with diameter ratio of the thickness Dт /Sm wall > 8. The results of the study are intended for industrial use in the production of pipes with the ratio Dt/Sm = 8 – 15 with tolerances on wall thickness ±6 %; diameter ±0,5 %. These results would increase the understanding and especially the process of obtaining thin-walled pipes on pipe-rolling units with roll-off of screw rolling mills.
About the Authors
E. A. Kharitonov
National University of Science and Technology “MISIS” (MISIS)
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Assist. Professor , Senior Researcher of the Chair “Metal Forming”,
Moscow
V. P. Romanenko
National University of Science and Technology “MISIS” (MISIS)
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Professor of the Chair “Metal Forming”,
Moscow
A. S. Budnikov
National University of Science and Technology “MISIS” (MISIS)
Russian Federation
Russian Federation
MA Student, Engineer of the Chair “Metal Forming”,
Moscow
References
1. Kolikov A.P., Romantsev B.A. Teoriya obrabotki metallov davleniem: uchebnik [Theory of metal forming: textbook]. Moscow: Izd. Dom MISiS, 2015, 451 p. (In Russ.).
2. Danchenko V.N., Kolikov A.P., Romantsev B.A., Samusev S.V. Tekhnologiya trubnogo proizvodstva: ucheb. dlya vuzov [Pipe production technology: textbook for universities]. Moscow: Intermetinzhiniring, 2002, 640 p. (In Russ.).
3. Shevakin Yu.F., Kolikov A.P., Raikov Yu.N. Proizvodstvo trub: ucheb. dlya vuzov [Pipe production: textbook for universities]. Moscow: Intermet Inzhiniring, 2005, 568 p. (In Russ.).
4. Gromov N.P. Teoriya obrabotki metallov davleniem: ucheb. dlya vuzov [Theory of metal forming: : textbook for universities]. Moscow: Metallurgiya, 1978, 360 p. (In Russ.).
5. Teterin P.K. Teoriya poperechno-vintovoi prokatki [Theory of crossscrew rolling]. Moscow: Metallurgiya 1971, 368 p. (In Russ.).
6. Romantsev B. A., Goncharuk A.V., Vavilkin N.M., Samusev S.V. Obrabotka meallov davleniem: uchebnik [Metal forming: textbook]. Moscow: Izd. dom MISiS, 2008, 960 p. (In Russ.).
7. Potapov I.N., Polukhin P.I. Tekhnologiya vintovoi prokatki [Technology of screw rolling]. Moscow: Metallurgiya, 1990. 344 p. (In Russ.).
8. Nikulin A.N. Vintovaya prokatka. Napryazheniya i deformatsii. Monografi ya [Screw rolling. Stress and strain. Monograph]. Moscow: Metallurgiya 2014, 380 p. (In Russ.).
9. Danchenko V.N., Kolikov A.P., Romantsev B.A., Samusev S.V. Tekhnologiya trubnogo proizvodstva: uchebnik dlya vuzov [Technology of pipe production: textbook for universities]. Moscow: Intermet Inzhiniring, 2002, 640 p. (In Russ.).
10. Potapov I.N., Kolikov A.P., Druyan V.M. Teoriya trubnogo proizvodstva [Theory of pipe production]. Moscow: Metallurgiya 1991, 399 p. (In Russ.).
11. Lakashin N.D., Kokhan L.S. Obrabotka metallov davleniem: ucheb posobie dlya vuzov [Metal forming: manual]. Moscow: MGVMI, 2006, 424 p. (In Russ.).
12. Kharitonov E.A., Burov I.A., Vol’shonok I.Z., Kharitonov D.E. Features of the roll gap geometry and sizing of mill radial-shear rolls at high angles of supply. Tsvetnye metally, 1995, no. 8, pp. 64–66. (In Russ.).
13. Kharitonov E.A., Burov I.A., Romanenko V.P., Vol’shonok I.Z. Improvement of angle computation method for deformation and grooving of rolls at continuous billet multiroll mill with large roll feed direction. Moscow: Izvestiya VUZov. Chernaya metallurgiya = Izvestiya. Ferrous Metallurgy, 2010, no. 3, pp. 29–31. (In Russ.).
14. Kharitonov E.A., Romanenko V.P., Budnikov A.S. Pipe Behavior in a Three-Roller Screw-Rolling Mill. Steel in Translation, vol. 44, no. 10, pp. 769–772.
15. Parshin V.S., Karamyshev A.L., Nekrasov I.I., Pugin A.I., Fedulov A.A. Prakticheskoe rukovodstvo k programmnomu kompleksu DEFORM 3D: uchebnoe posobie [A practical guide to program complex DEFORM 3D: manual]. Ekaterinburg: UrFU, 2010, 266 p. (In Russ.).
Review
For citations:
Kharitonov E.A., Romanenko V.P., Budnikov A.S. DEVELOPMENT OF CALCULATING METHOD OF THE DEFORMATION PARAMETERS DURING ROLLING OUT IN A THREE-ROLL MILL LINERS OF SCREW ROLLING. Izvestiya. Ferrous Metallurgy. 2016;59(3):167-172. (In Russ.) https://doi.org/10.17073/0368-0797-2016-3-167-172
Views:
606
Email this article 