INFLUENCE OF THE QUENCHING TECHNOLOGIES ON THE JOINT BAR MICROSTRUCTURE
https://doi.org/10.17073/0368-0797-2015-9-682-687
Abstract
Joint bar (fishplate) is an asymmetrical cross-section product with different mass elements – the web, the upper and lower bulbous heads. Technical standards specify the strict requirements on the joint bar mechanical properties and straightness. The microstructure after rolling (without heat treatment), after thermostrengthening according to the traditional technology – oil quenching, and accelerated water cooling technology has been studied by using optical and scanning electron microscope. The accelerated water cooling technology was the first implemented in industry for asymmetrical cross-section body. As a result, it was found that a high degree dispersion of the phases and the small grain size provided the best results in stable mechanical properties, which is typical for the sprayer system. The joint bar straightness is achieved in response to the cooling process controllability.
About the Authors
M. V. Zakharchenko
Ural Federal University named after the first President of Russia B.N. Yeltsin
Russian Federation
Russian Federation
Postgraduate of the Chair “Metal Science and Heat Treatment”,
19, Mira str., Ekaterinburg, 620002
A. Yu. Zhilyakov
Ural Federal University named after the first President of Russia B.N. Yeltsin
Russian Federation
Russian Federation
Senior Engineer of the Chair of Physics and Heat Treatment of Metals,
19, Mira str., Ekaterinburg, 620002
Yu. I. Lipunov
OJSC Research Institute of Metallurgical Heat Engineering (VNIIMT)
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Director of the Center of Modern Cooling Systems and Thermohardening Metals Technologies,
16, Studencheskaya str., Ekaterinburg, 620137
K. Yu. Eismondt
OJSC Research Institute of Metallurgical Heat Engineering (VNIIMT)
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Deputy Director of the Center of Modern Cooling Systems and Thermohardening Metals Technologies,
16, Studencheskaya str., Ekaterinburg, 620137
Yu. G. Yaroshenko
Ural Federal University named after the first President of Russia B.N. Yeltsin
Russian Federation
Russian Federation
Dr. Sci. (Eng.), Professor of the Chair “Metal Science and Heat Treatment”,
19, Mira str., Ekaterinburg, 620002
References
1. Ivanov P.S., Dan’kov S.F., Yuzyk O.V., Shishmaev A.A. New resource-saving technologies in the rail sector. Put’ i putevoe khozyaistvo. 2011, no. 7, pp. 23–25. (In Russ.).
2. GOST 4133-73. Nakladki rel’sovye dvukhgolovye dlya zheleznykh dorog shirokoi kolei. Tekhnicheskie trebovaniya [State standard 4133-73. Two-headed rail pads for broad gauge railways. Technical requirements]. Moscow: IPK Izdatel’stvo standartov, 1998. 7 p. (In Russ.).
3. Yaroshenko Y.G., Lipunov Y.I., Startseva M.V. etc. Developing a modern thermal strengthening technique for regulated fishplate cooling. Energy Production and Management in the 21st Century. The Quest for Sustainable Energy. 2014. Vol. 1, pp. 491–501.
4. Zakharchenko M.V. Razrabotka i vnedrenie ustroistva i tekhnologii uskorennogo okhlazhdeniya dlya obespecheniya mekhanicheskikh svoistv metalla rel’sovykh nakladok»: dis. …kand. tekhn. nauk [Development and implementation of equipment and technology of rapid cooling to ensure the mechanical properties of the metal of rail lining. Cand. Tech. Sci. Diss.]. Ekaterinburg, 2014. 136 p. (In Russ.).
5. GOST 5639-82. Stali i splavy. Metody vyyavleniya i opredeleniya velichiny zerna [State standard 5639-82. Metals and alloys. Methods for detection and determination of the grain size]. Moscow: IPK Izdatel’stvo standartov, 2003. 38 p. (In Russ.).
6. TU 14-2R-463-2011. Proizvodstvo nakladok dvukhgolovykh dlya zheleznodorozhnykh rel’sov tipov R50 i R65 [Production of linings for the two-headed rails of R50 and R65 types]. 2011. 10 p. (In Russ.).
7. Otrabotka tekhnologii termouprochneniya rel’sovykh nakladok na opytnom stende OAO «VNIIMT»: otchet o NIR [Testing technology thermostrengthening of rail pads on the test stand of OJSC”VNIIMT”: report on research]. Ekaterinburg : OAO “VNIIMT”, 2012, pp. 45–47. (In Russ.).
Review
For citations:
Zakharchenko M.V., Zhilyakov A.Yu., Lipunov Yu.I., Eismondt K.Yu., Yaroshenko Yu.G. INFLUENCE OF THE QUENCHING TECHNOLOGIES ON THE JOINT BAR MICROSTRUCTURE. Izvestiya. Ferrous Metallurgy. 2015;58(9):682-687. (In Russ.) https://doi.org/10.17073/0368-0797-2015-9-682-687
Views:
580
Email this article 