THEORY AND PRACTICE OF RESOURCE-SAVING TECHNOLOGIES OF MILL BAR PRODUCTION AT THE OPERATING CONTINUOUS ROLLING MILLS
https://doi.org/10.17073/0368-0797-2015-5-322-327
Abstract
Based on the modeling results of the processes of high-quality
rolling in calibers of a simple form, the flow patterns of surface layers of the blanks and their influence on the formation of stress-strain state of the metal in the rolling process have been determined and confirmed experimentally. Subject to the formed recommendations a new calibration of rolls of roughing mill of continuous light-section mill 250-2 of OJSC «EVRAZ ZSMK» has been developed and passed the trial approbation. Its use has increased the yield in the production of high-quality rolled structural steel by 3 %. The evaluation to improve the production efficiency by increasing productivity in the implementation process of rolling-separation under the existing continuous light-section mill 250-1 of OJSC «EVRAZ ZSMK» has been conducted. A technique for determining the multiplicity of separation depending on the desired performance increments has been offered, as well as provided the guidance on the calculation of the speed limit in the roughing and finishing stand continuous mill, the actual data on the change of the total reduction ratio and speed conditions on groups stands in the preparation of rebars no. 10, no. 12, no. 14.
About the Authors
R. A. Fastykovskii
Siberian State Industrial University 42, Kirova str., Novokuznetsk, Kemerovo Region, 654007, Russia
Russian Federation
Russian Federation
Dr. Sci. (Eng.), Professor of the Chair of ferrous metallurgy “Metal Forming and Metal Science, OJSC “EVRAZ ZSMK”
A. A. Umanskii
Siberian State Industrial University 42, Kirova str., Novokuznetsk, Kemerovo Region, 654007, Russia
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Assist. Professor of the Chair of ferrous metallurgy
References
1. Asanov V.N., Steblov A.B., Tulupov O.N., Lenartovich D.V. Improved grooving when rolling round profiles and reinforcement. Steel in Translation. 2008, vol. 38, no. 11, pp. 929–931.
2. Utkin G.S., Rezvov B.S., Khramtsov V.V., Veis A.I., Yurkov V.I. Production intensification of surface defects at blanks producing. Proizvodstvo prokata. 2004, no. 4, pp. 18–22. (In Russ.).
3. Peretyat’ko V.N., Rogov Yu.E., Zhuravlev B.K., Nefedov V.M. Production of surface defects in box passes. Izvestiya vuzov. Chernaya metallurgiya = Izvestiya. Ferrous Metallyrgy. 2011, no. 2, pp. 26–29. (In Russ.).
4. Salganik V.M., Pesin A.M., Pustovoitov D.O. Behavior modelling of cross crotchcorner cracks of slab when rolling in horizontal rollers. Izvestiya vuzov. Chernaya metallurgiya = Izvestiya. Ferrous Metallyrgy. 2010, no. 3, pp. 22. (In Russ.).
5. Kadykov V.N., Mart’yanov Yu.A., Umanskii A.A. Impact of roll pass design on the production of surface defects. Vestnik gorno-metallurgicheskoi sektsii RAEN. Otdelenie metallurgii. 2011, Issue 27, pp. 132–136. (In Russ.).
6. Umanskii A.A., Mart’yanov Yu.A. Process modeling of the production of surface defects of blanks at different conditions of rolling. Vestnik gorno-metallurgicheskoi sektsii RAEN. Otdelenie metallurgii. 2012, Issue 30, pp. 51–58. (In Russ.).
7. Slednev V.P. Sparennaya prokatka sortovykh profilei [Duplex rolling of section bars]. Moscow: Metallurgiya, 1988. 167 p. (In Russ.).
8. Shul‘gin G.M., Necheporenko V.A., Sheremet V.A., Kostyuchenko M.I., Minaev A.A., Babenko M.A., Kukui D.P., Korin‘ A.A. Two-pass rolling-division of reinforcing steel at Krivorozhskii integrated iron-and-steel works «Krovorozhstal’». Proizvodstvo prokata. 1998, no. 3, pp. 12–17. (In Russ.).
9. Matsuo G, Suzuki M. The latest Technology of Multy – slit rolling. SEA. ISI Quaterly. 1995, no. 3, pp. 49–58.
10. Zhuchkov S.M. Particularities in technological scheme for process of three-strand rolling-slitting at 320/150 wire-rod mill. Metallurg. 2001, no. 1, pp. 46–47.
11. Efimov O.Yu., Chinokalov V.Ya., Fastykovskii A.R., Kopylov I.V. Employing rolling and separation technology in the 250-1 mill. Steel in Translation. 2008, no. 8, pp. 671-673.
12. Zhuchkov S.M. Particularities in design of device for slitting the workpiece in three-strand rolling-slitting process. Metallurg. 2000, no. 11, pp. 42–43.
13. Fastykovskii A.R., Volkov K.V., Peretyat’ko V.N. etc. Improvement of the production technique of rebars at continuous light-section rolling mill. Izvestiya vuzov. Chernaya metallurgiya = Izvestiya. Ferrous Metallyrgy. 2011, no. 10, pp. 18–21. (In Russ.).
14. Perunov G.P., Limankin V.V., Volkov K.V., Baldin S.M., Chizh S.A., Sukhoplyuev V.A., Shesternin A.P., Smirnov V.K., Ignatovich Yu.V. Development of the rolling-division technology of reinforcing steel at light-section wire mill 320/150 of JSC «Amurmetall». Proizvodstvo prokata. 2006, no. 10, pp. 16–19. (In Russ.).
Review
For citations:
Fastykovskii R.A., Umanskii A.A. THEORY AND PRACTICE OF RESOURCE-SAVING TECHNOLOGIES OF MILL BAR PRODUCTION AT THE OPERATING CONTINUOUS ROLLING MILLS. Izvestiya. Ferrous Metallurgy. 2015;58(5):322-327. (In Russ.) https://doi.org/10.17073/0368-0797-2015-5-322-327
Views:
730
Email this article 