Application of physical simulation to evaluate the impact of teeming method and rate on axial zone formation of large ingots

The article presents the results of evaluation of the impact of teeming method and rate on solidification and formation of the axial zone of large ingots. The research is based on a physical simulation. With this aim a laboratory-scale plant (a crystallization mould) was designed and built which enabled to visualize and monitor solidification and structural formation of the model ingots. Sodium thiosulphate (crystal hyposulphite) – Na₂S₂O₃·5H₂O was used as a modeling solution. Matching of the processes in the model and in real industrial conditions of ingot teeming was assessed with similarity criteria obtained on the basis of the dimension theory with consideration of the physical and chemical processes in the ingot during its teeming and crystallization. Two methods – downhill casting and uphill casting – were used to teem the melt into the mould. During teeming the geometry and technological parameters of the model ingots remained unchanged while the teeming rate was altered. Length and medium width of the model ingot axial zone were measured. The thermal profiling of the surface of the mould model was monitored over the entire period of solidification to evaluate the thermal field alteration while the ingot was teemed and crystallized. Thermal imaging processing made it possible to observe temperature changes of the surface of the model mould from top to bottom for downhill cast ingots teemed at different rates. The results obtained demonstrate that teeming rate has a noticeable impact on the axial zone length. It was established that a decreased rate leads to an increased directionality of crystallization and improvement of the ingot axial zone structure.

1. Skoblo S.Ya., Kazachkov E.A. Ingots for Large Forgings. Moscow: Metallurgiya, 1973, 247 p. (In Russ.).

2. Smirnov A.N., Makurov S.L., Safonov V.M., Tsuprun A.Yu. Large Ingot. Donetsk: Veber, 2009, 279 p. (In Russ.).

3. Zhul’ev S.I., Zyuban N.A. Production of Forging Ingots and Problems with Their Quality. Volgograd: RPK “Politekhnik”, 2003, 168 p. (In Russ.).

4. Qian S., Hu X., Cao Y., Kang X., Li D. Hot top design and its influence on feeder channel segregates in 100-ton steel ingots. Materials & Design. 2015, vol. 87, pp. 205–214. https://doi.org/10.1016/j.matdes.2015.07.150

5. Zyuban N.A., Rutskii D.V., Gamanyuk S.B., Styazhin A.N., Sidorov A.A. Cast-structure defects in the axial zone of 38XH3MΦA steel ingots and their behavior in upsetting. Steel in Translation. 2011, vol. 41, no. 4, pp. 318–322. https://doi.org/10.3103/S0967091211040255

6. Tashiro K., Watanabe S., Kitagawa I., Tamura I. Influence of mould design on the solidification and soundness of heavy forging ingots. Transactions of the Iron and Steel Institute of Japan. 1983, vol. 23, no. 4, pp. 312–321. https://doi.org/10.2355/isijinternational1966.23.312

7. Gamanyuk S.B. Investigation of a large forging steel ingot of modified geometry in order to improve the quality of metal forgings: Cand. Tech. Sci. Diss. Volgograd: 2012, 162 p. (In Russ.).

8. Romashkin A.N., Malginov A.N., Tolstyh D.S., Ivanov I.A., Doub V.S. The ingot geometry effect on the axial shrinkage. Computer Research and Modeling. 2015, Vol. 7, no. 1, pp. 107–112. (In Russ.). https://doi.org/10.20537/2076-7633-2015-7-1-107-112

9. Wang J., Fu P., Liu H., Li D., Li Y. Shrinkage porosity criteria and optimized design of a 100-ton 30Cr2Ni4MoV forging ingot. Mate­rials & Design. 2012, vol. 35, pp. 446–456. https://doi.org/10.1016/j.matdes.2011.09.056

10. Zhang C.-J., Bao Y.-P., Wang M. Influence of casting parameters on shrinkage porosity of a 19 ton steel ingot. Metallurgia Italiana. 2016, vol. 108, no. 1, pp. 37–44.

11. Zhang C.-J., Bao Y.-P., Wang M., Guo B. Influence of casting parameters on the shrinkage porosity of a 40 ton steel ingot by numerical simulation. Proceedings of the 6th Int. Congress on the Science and Technology of Steelmaking, 2015, pp. 543–546.

12. Yu Z., Zhang H., Wang X., Wu X. Study on heat transfer characteristics during solidification of 18-ton steel ingot with large ratio of height to diameter. Metallurgia Italiana. 2020, vol. 112, no. 5, pp. 37–47.

13. Zhang C., Loucif A., Jahazi M., Morin J.-B. FE modelling and prediction of macrosegregation patterns in large size steel ingots: Influence of filling rate. Metals. 2022, vol. 12, no. 1, article 29. https://doi.org/10.3390/met12010029

14. Zhang C., Loucif A., Jahazi M., Tremblay R., Lapierre L.-P. On the effect of filling rate on positive macrosegregation patterns in large size cast steel ingots. Applied Sciences (Switzerland). 2018, vol. 8, no. 10, article 1878. https://doi.org/10.3390/app8101878

15. Marx K., Rödi S., Schramhauser S., Seemann M. Optimization of the filling and solidification of large ingots. Metallurgia Italiana. 2014, vol. 106, no. 11–12, pp. 11–19.

16. Romashkin A.N., Mal’ginov A.N., Dub V.S., Kolpishon E.Yu. Features of uphill casting of ingots. Elektrometallurgiya. 2013, vol. 1, pp. 18–23. (In Russ.).

17. Duan Z., Shen H., Liu B. Numerical simulation of solidification and macrosegregation in water cooled heavy steel ingot. Proceedings of the 8th Pacific Rim Int. Congress on Advanced Materials and Processing (PRICM-8). 2016, pp. 3025–3032. https://doi.org/10.1007/978-3-319-48764-9_374

18. Chen Z., Zhai Q., Zhang J. Validation and numerical simulation for shrinkage porosity of a X12 steel ingot. TMS 2015 144th Annual Meeting & Exhibition. 2015, pp. 1209–1216. https://doi.org/10.1007/978-3-319-48127-2_146

19. Lü N., Jin Y., Li S., Ai X., Yuan X. Numerical simulation on gradient cooling behavior of jumbo slab ingot. China Foundry. 2013, vol. 10, no. 2, pp. 87–91.

20. Kotásek O., Kurka V., Vindyš M., Jonšta P., Noga R., Dobiáš M. Comparison of casting and solidification of 12 ton steel ingot using two different numerical software. Proceedings 30th Anniversary Int. Conf. on Metallurgy and Materials. 2021, pp. 147–152. https://doi.org/10.37904/metal.2021.4091

21. Romashkin A.N., Dub V.S., Ivanov I.A., Markov S.I., Mal’gi­nov A.N., Tolstykh D.S. Development of an integral production process for manufacturing machinery billets based on computer simulation. Metallurgist. 2015, vol. 58, no. 9–10, pp. 821–830. https://doi.org/10.1007/s11015-015-0002-z

22. Kang J., Zhang C., Dong C., Shen H., Liu B. Water analogy experiment on the multi-concentration pouring process of a 585 ton steel ingot. Frontiers in Materials Processing, Applications, Research and Technology. 2018, pp. 107–121. https://doi.org/10.1007/978-981-10-4819-7_11

23. Dub V.S., Romashkin A.N., Tolstykh D.S., Mal’ginov A.N., Ivanov I.A., Ekhvaya G.A. Analysis of the kinetics of the solidification of steel forging ingots of different configurations. Part I. Results from cold modeling. Metallurgist. 2016, vol. 59, no. 11–12, pp. 1040–1052. https://doi.org/10.1007/s11015-016-0213-y

24. Ludwig A., Stefan-Kharicha M., Kharicha A., Wu M. Massive formation of equiaxed crystals by avalanches of mushy zone segments. Metallurgical and Materials Transaction A. 2017, vol. 48, pp. 2927–2930. https://doi.org/10.1007/s11661-017-4008-y

25. Stefan-Kharicha M., Kharicha A., Mogeritsch J., Wu M., Ludwig A. Review of ammonium chloride-water solution properties. Journal of Chemical and Engineering. 2018, vol. 63, pp. 3170–3183. https://doi.org/10.1021/acs.jced.7b01062

26. El’darkhanov A.S., Efimov V.A., Nuratdinov A.S. Casting Proces­ses and Their Modeling. Moscow: Mashinostroenie, 2001, 208 p. (In Russ.).

27. Smirnov A.N., Pilyushenko V.L., Momot S.V., Amitan V.N. Solidification of Metal Melt under External Influences. Donetsk: VIK, 2002, 169 p. (In Russ.).

28. Leibenzon V.A., Nedopekin F.V., Kondratenko V.M. Solidification of Metal Compositions: Production and Modeling. Donetsk: Yugo-vostok Ltd., 2005, 231 p. (In Russ.).

29. Gamanyuk S.B., Zyuban N.A., Rutskii D.V., Palatkin S.V. Device for studying the process of ingots crystallization in a mill. Patent RF no. 169365. MPK B22D 7/08. Bulleten’ izobretenii. 2017, no. 8. (In Russ.).