Preview

Izvestiya. Ferrous Metallurgy

Advanced search

Statistical modeling of temperature operating modes of heating furnaces for hot strip mills

https://doi.org/10.17073/0368-0797-2021-5-374-381

Abstract

The article provides a method of mathematical modeling to improve temperature operating modes of heating furnaces for hot strip mills. The object of the research is the thermal operation of a continuous walking beam furnace for heating slabs before rolling. The subject of the research is statistical modeling of metal heating in furnaces of this type. The creation of a statistical model consists of factors selection, construction of regression model, correlation analysis and assessment of the variables significance, adjustment of factors and obtaining regression equations. The main part of the research refers to a statistical model based on a comprehensive analysis. This model is based on the results of 15 automated industrial experiments on Russian heating furnaces of hot strip mills and describes the heating process in walking-beam furnace with acceptable accuracy. The adaptation of the statistical model and error calculation has been carried out. The article contains graphs comparing real temperatures and temperatures calculated on the basis of mathematical and statistical models for one of the experiments. The main conclusions are formulated based on the results of the research done. For the first time in metallurgical practice, a statistical model has been developed that describes the process of metal heating in a five-zone continuous furnace with eight heating subzones. Since the regression function is defined, interpreted and justified, and the assessment of the accuracy of the regression analysis meets the requirements, it can be assumed that the model and predicted values have sufficient reliability.

About the Authors

M. Zh. Bogatova
National University of Science and Technology “MISIS”
Russian Federation

Maiya Zh. Bogatova, Postgraduate of the Chair “Energy-Efficient and Resource-Saving Industrial Technologies”

4 Leninskii Аve., Moscow 119049



S. I. Chibizova
National University of Science and Technology “MISIS”
Russian Federation

Svetlana I. Chibizova, Cand. Sci. (Eng.), Assist. Prof. of the Chair “Energy-Efficient and Resource-Saving Industrial Technologies”

4 Leninskii Аve., Moscow 119049



References

1. Belen’kii A.M., Bursin A.N., Ulanovskii A.A., Chibizova S.I. Improvement in thermal operation of heating furnaces for hot rolling mills. Chernaya metallurgiya. Bulletin of Scientific, Technical and Economic Information. 2015, no. 2, pp. 62–69. (In Russ.).

2. Belen’kii A.M., Bursin A.N., Mordovkin D.S., Ulanovskii A.A., Chibizova S.I. Problems of improvement in thermal operation of heating furnaces for hot rolling mills. In: XI Congress of Rollermen: Proceedings. Vol. 1. Magnitogorsk, 2017, pp. 29–35. (In Russ.).

3. Mordovkin D.S. Research and optimization of heating technology of continuously cast slabs in continuous furnace: Cand. Tech. Sci. Diss. Lipetsk: 2011, 214 p. (In Russ.).

4. Orelkina D.I., Petelin A.L., Polulyakh L.A., Podgorodetskii G.S. Calculation model for the concentration of secondary metallurgical emissions into the atmosphere. Izvestiya. Ferrous Metallurgy. 2016, vol. 59, no. 5, pp. 300–305. (In Russ.). http://doi.org/10.17073/0368-0797-2016-5-300-305

5. Favennec Y., Labb V., Bay F. Induction heating processes optimization a general optimal control approach. Journal of Computational Physics. 2003, vol. 187, no. 1, pp. 68–94. http://doi.org/10.1016/S0021-9991(03)00081-0

6. Feischl M., Führer T., Niederer M., Strommer S., Steinboeck A., Praetorius D. Efficient numerical computation of direct exchange areas in thermal radiation analysis. Numerical Heat Transfer, Part B – Fundamentals. 2016, vol. 69, no. 6, pp. 511–533. http://doi.org/10.1080/10407790.2016.1173469

7. Wang H. Mathematical heat transfer model research for the improvement of continuous casting slab temperature. ISIJ International. 2005, vol. 45, no. 9, pp. 1291–1296. https://doi.org/10.2355/isijinternational.45.1291

8. Antipkina M.E., Krupennikov S.A., Levitskii I.A. Determination of optimum lining thickness for a heating furnace. Refractories and Industrial Ceramics. 2020, vol. 60, no. 5, pp. 510–515. http://doi.org/10.1007/s11148-020-00395-2

9. Arutyunov V.A., Bukhmirov V.V., Krupennikov S.A. Mathematical Modeling of Industrial Furnaces Thermal Operation. Moscow: Metallurgiya, 1990, 239 p. (In Russ.).

10. Arutyunov V.A., Levitskii I.A., Ibadullaev T.B. Development of methods for mathematical modeling of thermophysical processes in industrial fuel furnaces. Metallurgist. 2011, vol. 55, no. 1–2, pp. 3–9. http://doi.org/10.1007/s11015-011-9385-7

11. Alizadeh M., Edris H., Shafyei A. Mathematical modeling of heat transfer for steel continuous casting process. International Journal of ISSI. 2006, vol. 3, no. 2, pp. 7–16.

12. Chen W.H., Chung Y.C., Liu J.L. Analysis on energy consumption and performance of reheating furnaces in a hot strip mill. International Communications in Heat and Mass Transfer. 2005, vol. 32, no. 5, pp. 695–706. http://doi.org/10.1016/j.icheatmasstransfer.2004.10.019

13. Chen Y.W., Chai T.Y. Modelling and prediction for steel billet temperature of heating furnace. International Journal of Advanced Mechatronic Systems. 2010, vol. 2, no. 5-6, pp. 342–349.

14. Storck J., Lindberg B. A cost model for the effect of setup time reduction in stainless steel strip production. In: Proceedings, 1st Swedish Production Symposium. Gothenburg, Sweden, 2007, pp. 1–8.

15. Han S.H., Chang D., Kim C.Y. A numerical analysis of slab heating characteristics in a walking beam type reheating furnace. International Journal of Heat and Mass Transfer. 2010, vol. 53, no. 19-20, pp. 3855–3861. http://doi.org/10.1016/j.ijheatmasstransfer.2010.05.002

16. Wild D., Meurer T., Kugi A. Modelling and experimental model validation for a pusher-type reheating furnace. Mathematical and Computer Modelling of Dynamical Systems. 2009, vol. 15, no. 3, pp. 209–232. http://doi.org/10.1080/13873950902927683

17. Belen’kii A.M., Dubinskii M.Yu., Kalimulina S.I. Factory testing – The basis for implementing an energy-saving policy in metallurgical heat engineering. Metallurgist. 2010, vol. 54, no. 5-6, pp. 263–267. http://doi.org/10.1007/s11015-010-9290-5

18. Belen’kii A.M., Dubinskii M.Yu., Ladygichev M.G. Temperature: Theory, Practice, Experiment. Vol. 2: Temperature Measurement in Industry and Power Engineering. Moscow: Teplotekhnik, 2007, 736 p. (In Russ.).

19. Ulanovskii A.A., Taake M., Belen’kii A.M., Bursin A.N., Chibizova S.I. Using a Phoenix TM autonomous automated system for monitoring temperature field of metal to be heated in metallurgical furnaces. Chernye metally. 2019, no. 9, pp. 59–64. (In Russ.).

20. Bogatova M.Zh., Chibizova S.I. Statistical modeling of temperature operating modes of heating furnaces for strip hot rolling mill. In: Proceedings of the IX Int. Sci. and Pract. Conf. “Energy-Efficient and Resource-Saving Industrial Technologies. Furnace Aggregates. Ecology” December 12–14, 2018, Moscow, pp. 196–203. (In Russ.).

21. Radchenko Yu.S. Basics of Statistical Modeling: Manual for Universities. Voronezh: VSU, 2010, 30 p. (In Russ.).

22. Ulanovskii A.A., Belen’kii A.M. Improving efficiency of heating furnaces of rolling mills. In: Proceedings of the IX Int. Sci. and Pract. Conf. “Energy-Efficient and Resource-Saving Industrial Technologies. Furnace Aggregates. Ecology”. Moscow: NUST “MISIS”, 2012, pp. 472–484. (In Russ.).

23. Carlsson L.S., Samuelsson P.B., Jönsson P.G. Using statistical modeling to predict the electrical energy consumption of an electric arc furnace producing stainless steel. Metals. 2020, vol. 10, no. 1, article 36. http://doi.org/10.3390/met10010036

24. Hsieh C.T., Huang M.J., Lee S.T. Numerical modeling of a walkingbeam-type slab reheating furnace. Numerical Heat Transfer; Part A – Applications. 2008, vol. 53, no. 9, pp. 966–981. http://doi.org/10.1080/10407780701789831

25. Kim J.G., Huh K.Y., Kim I.T. Three-dimensional analysis of the walking-beam-type slab reheating furnace in hot strip mills. Numerical Heat Transfer; Part A – Applications. 2000, vol. 38, no. 6, pp. 589–609. http://doi.org/10.1080/104077800750021152

26. Santos C.P., Giacomin C.N. Computer simulation of slab reheating process in walking beam furnaces. Tecnologia em Metalurgia e Materiais. 2008, vol. 5, no. 1, pp. 35–39.


Review

For citations:


Bogatova M.Zh., Chibizova S.I. Statistical modeling of temperature operating modes of heating furnaces for hot strip mills. Izvestiya. Ferrous Metallurgy. 2021;64(5):374-381. (In Russ.) https://doi.org/10.17073/0368-0797-2021-5-374-381

Views: 659


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 0368-0797 (Print)
ISSN 2410-2091 (Online)