Quality improvement of calibrated steel by surface deformation. Part 1. Determination of the stressed state of cylinderical parts during orbital surface deformation

Cold drawn calibrated steel is an effective blank for the manufacture of low-rigid cylindrical parts such as shafts and axles. High accuracy of the diametric size along the length of the workpiece, low surface roughness, increased hardness and strength of the surface layer compared to hot rolled products allow us to produce a variety of parts with high metal utilization and high machining performance. The main disadvantage of calibrated metal is the residual stresses that occur during pressure treatment. To reduce or change the nature of the distribution over the cross section, it is proposed to use small plastic deformations in the surface layer of the hire. Known in practice methods of surface plastic deformation (PPD) usually lead to the curvature of non-rigid workpieces. To intensify the stress-strain state in the deformation zone, we propose a method of orbital surface deformation. Based on the finite element modeling, influence of the main parameters of orbital surface deformation on stress state in the deformation zone and residual stresses in the finished products is considered. Compared with the traditional PPD process, the stress intensity during orbital surface deformation will increase by 10 – 15 %. The residual compressive stresses that form in the surface layers reach 70 – 85 % of the material tensile strength. In the second part of the article, it is supposed to provide information on a more effective method of surface deformation and on the change in initial residual stresses that are formed during the calibration of cylindrical rods.

1. Zaides S.A. Okhvatyvayushchee poverkhnostnoe plasticheskoe deformirovanie [Encompassing Surface Plastic Deformation]. Irkutsk: Izd-vo IrGTU, 2001, 309 p.

2. Sheftel’ N.I. Uluchshenie kachestva i sortamenta prokata [Improving the Quality and Range of Products]. Moscow: Metallurgiya, 1973, 343 p. (In Russ.).

3. Vishnyakov Y.D., Piskarev V.D. Upravlenie ostatochnymi napryazheniyami v metallakh i splavakh [Management of Residual Stresses in Metals and Alloys]. Moscow: Metallurgiya, 1989, 253 p. (In Russ.).

4. Papshev D.D. Otdelochno-uprochnyayushchaya obrabotka poverkhnostnym plasticheskim deformirovaniem [Finishing and Hardening Treatment by Surface Plastic Deformation]. Moscow: Mashinostroenie, 1987, 152 p. (In Russ.).

5. Totten G., Howes M., Inoue T. Handbook of Residual Stress and Deformation of Steel. USA: ASM International, Materials Park, Ohio, 2002, 500 p.

6. Handbook of Residual Stress and Distortion of Steel. Totten G., Howes M., Inoue T. eds. Publications for ASTM (The American Society for Testing and Materials), 2002, 449 p.

7. Ebert L.J. The role of residual stresses in the mechanical performance of case carburized steel. Metal Transactions A. 1978, vol. 9A, pp. 1537–1551. 8. Swic A., Taranenko V., Wolos D. New method for machining of low-rigidity shafts. Advances in Manufacturing Science and Technology. 2010, vol. 34, no. 1, pp. 59–71.

8. Skorokhodov A.N., Zudov E.G., Kirichkov A.A., Petrenko Yu.P. Ostatochnye napryazheniya v profilyakh i sposoby ikh snizheniya [Residual Stresses in the Profiles and Ways to Reduce Them]. Moscow: Metallurgiya, 1985, 185 p. (In Russ.).

9. Odintsov L.G. Uprochnenie i otdelka detalei poverkhnostnym plasticheskim deformirovaniem: spravochnik [Hardening and Finishing of Parts by Surface Plastic Deformation: a Guide]. Moscow: Mashinostroenie, 1987, 328 p. (In Russ.).

10. Dimarogonas A.D. Dynamic instability of shafts during machining. Journal of Sound and Vibration. 1986, vol. 108, no. 2, pp. 181–189.

11. Kramer I.R. Effect of surfaces on mechanical behavior of metals. In: Surface Phenomena. Bonis L.J., Bruyn P.L., Duga J.J. eds. Springer US, 1995, pp. 171–193.

12. Bussu G., Irving P.E. The role of residual stress and heat affected zone properties on fatigue crack propagation in friction stir welded 2024-T351 aluminium joints. Int. Journal of Fatigue. 2003, vol. 25, no. 1, pp. 77–88.

13. Blуumenshtein V.Yu., Krechetov A.A., Makhalov M.S. Modern competitive technologies for finishing and hardening processing by surface plastic deformation. Uprochnyayuschie technologii i pokrytiya. 2012, no. 7, pp. 7–12. (In Russ.).

14. Lebedev V.A. Effektivnye technologii poverkhnostnogo plasticheskogo deformirovaniya i kombinirovannoi obrabotki [Effective Technologies of Surface Plastic Deformation and Combined Processing]. Kirichek A.V. ed. Moscow: ID “Spectr”, 2014, 403 p. (In Russ.).

15. Zaides S.A. New methods of surface plastic deformation in the manufacture of machine parts. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta im. G.I. Nosova. 2018, vol. 16, no. 3, pp. 129–139. (In Russ.).

16. Zaides S.A., Nguyen Van Huan. Determination of residual stresses in the calibrated roll. Izvestiya. Ferrous Metallurgy. 2017, vol. 60, no. 2, pp. 109–115. (In Russ.).

17. Tekhnologiya i instrumenty otdelochno-uprochnyayushchei obrabotki detalei poverkhnostnym plasticheskim deformirovaniem: spravochnik: v 2-kh tomakh. T. 1 [Technology and Tools for Finishing and Hardening of Parts by Surface-Plastic Deformation: a Reference Book in 2 Vols. Vol. 1]. Suslov A.G. ed. Moscow: Mashinostroenie, 2014, 480 p. (In Russ.).

18. Blуumenshtein V.Yu., Makhalov M.S. Influence of the modes on formation of residual stresses in surface layer during dimensional combined rolling. Obrabotka metallov. 2008, no. 2, pp. 15–22. (In Russ.).

19. Hauk V. Structural and Residual Stress Analysis by Nondestructive Methods: Evaluation, Application, Assessment. Amsterdam: Elsevier Science B.V. 1997, 640 p.

20. Zaides S.A., Pham Van Anh. Sposob poverkhnostnogo plasticheskogo deformirovaniya [The method of surface plastic deformation]. Patent RF no. 2019105314, publ. 29.11.2019. (In Russ.).

21. Bakov K.A. ANSYS. Spravochnik pol’zovatelya [ANSYS. User Reference]. Moscow: DMK Press, 2005, 640 p. (In Russ.).

22. Bruyaka V.A., Fokin V.G., Kuraeva Y.V. Inzhenernyi analiz v ANSYS Workbench [Engineering Analysis at ANSYS Workbench]. Samara: Samar. gos. tekhn. un-t, 2013, 109 p. (In Russ.).