Stress-strain state of metal in deformation zone during production of steel section billets on the unit of combined continuous casting and deformation. Report 2
https://doi.org/10.17073/0368-0797-2020-9-730-734
Abstract
Stress state of metal in deformation zone during introduction of the separating collars of the grooved die into continuously casted steel slab was calculated for production of section billets on the unit of combined continuous casting and deformation. Calculation of axial, tangential and equivalent stresses arising in deformation zone of metal was made in four sections of deformation zone and its results are presented in specific points and lines. View of the section of deformation zone and location of specific points are provided. The stress state of metal in zone of cyclic deformation at formation of three steel section billets from continuously cast slab by separating collars of grooved die on the unit of combined continuous casting and deformation was determined by solving extensive problem of elasticity with the finite element method using the ANSYS package. The results of calculation of axial, tangential and equivalent stresses according to Mises in deformation zone are given in form of graphs and tables for working surfaces in four cross sections. The values and regularities of distribution of these stresses along the length and width of deformation zone were determined. The character of axial stresses distribution by characteristic lines located along the length of deformation zone is shown. Values of the highest compressive and tensile axial stresses arising in deformation zone during introduction of separating collars of grooved were obtained for the unit of combined continuous casting and deformation.
Keywords
installation,
continuous casting,
billet,
slab,
grooved die,
deformation zone,
final element,
stress
About the Authors
O. S. Lekhov
Russian State Vocational Pedagogical University
Russian Federation
Russian Federation
Dr. Sci. (Eng.), Professor of the Chair of Engineering and Vocational Training in Machinery and Metallurgy
Ekaterinburg
A. V. Mikhalev
Russian State Vocational Pedagogical University
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Senior Lecturer of the Chair of Engineering and Vocational Training in Machinery and Metallurgy
Ekaterinburg
References
1. Lekhov O.S., Mikhalev A.V. Stress-strain state of metal in deformation zone during production of steel section billets on the unit of combined continuous casting and deformation. Report 1. Izvestiya. Ferrous Metallurgy. 2020, vol. 63, no. 7, pp. 548–553. (In Russ.).
2. Lekhov O.S., Mikhalev A.V. Ustanovka sovmeshchennogo protsessa nepreryvnogo lit’ya i deformatsii dlya proizvodstva listov iz stali dlya svarnykh trub. Teoriya i raschet [Unit of Сombined Сontinuous Сasting and Deformation for Production of Steel Sheets for Welded Pipes. Theory and Design]. Ekaterinburg: Izd-vo UMTs UPI, 2017, 151 p. (In Russ.).
3. Lekhov O.S., Bilalov D.Kh. Technological capabilities of combined continuous casting and deformation units for production of metal products. Proizvodstvo prokata. 2016, no. 7, pp. 24–26. (In Russ.).
4. Lekhov O.S., Ukhlov I.V., Mikhalev A.V. Sposob nepreryvnogo lit’ya zagotovok i ustroistvo dlya ego osushchestvleniya [Method for continuous casting of billets and device for its implementation]. Patent RF no. 2658761. Byulleten’ izobretenii. 2018, no. 18. (In Russ.).
5. Mazur D.D., Khizhnyak V.L. Resistance of low-alloyed steels to deformation. Stal’. 1991, no. 8, pp. 41–43. (In Russ.).
6. Khenzel’ A., Shpittel’ T. Raschet energosilovykh parametrov v protsessakh obrabotki metallov davleniem [Calculation of Power Parameters in Metal Forming Processes]. Moscow: Metallurgiya, 1982, 360 p. (In Russ.).
7. Fujii H., Ohashi T, Hiromoto T. On the formation of the internal cracks in continuously cast slabs. Transactions of the Iron and Steel Institute of Japan. 1978, vol. 18, no. 8, pp. 510–518.
8. Sorimachi K., Emi T. Elastoplastic stress analysis of bulging as a major cause of internal cracks in continuously cast slabs. Tetsu to Hagane. 1977, vol. 63, no. 8, pp. 1297–1304.
9. Takashima Y., Yanagimoto I. Finite element analysis of flange spread behavior in H-beam universal rolling. Wiley in Steel Research International. 2011, vol. 82, pp. 1240–1247.
10. Kobayashi S., Oh S-I, Altan T. Metal forming and finite-element method. New York: Oxford University Press, 1989, 377 p.
11. Matsumia Т., Nakamura Y. Mathematical model of slab bulging during continuous casting. In: Applied Mathematical and Physical Models in Iron and Steel Industry. Proceedings of the 3 rd Process Technological Conference, Pittsburgh, Pa, 28-31 March 1982. New York, 1982, pp. 264–270.
12. Segerlind Larry J. Applied finite element analysis. New York etc., 1976. (Russ. ed.: Segerlind L. Primenenie metoda konechnykh elementov. Moscow: Mir, 1979, 393 p.).
13. Norrie D. H., de Vries G. An introduction to finite element analysis. Academic Press, New York, 1978. (Russ. ed.: Norrie D., de Vries G. Vvedenie v metod konechnykh elementov. Moscow: Mir, 1981, 304 p.).
14. Gallagher R.H. Finite Element Analysis: Fundamentals. PrenticeHall, New Jersey, 1975, 420 p. (Russ. ed.: Gallagher R. Metod konechnykh elementov. Osnovy. Moscow: Mir, 1984.).
15. Zienkiewicz O.C., Morgan K. Finite Elements and Approximation. New York: Wiley, 1983, 328 p. (Russ. ed.: Zienkiewicz O.C., Morgan K. Konechnye elementy i approksimatsiya. Moscow: Mir, 1986, 318 p.).
16. Pervez T., Seibi A., Karrech A. Simulation of solid tubular expansion in well drilling using finite element method. Journal of Petroleum Science and Technology. 2005, vol. 23, no. 7-8, pp. 775–794.
17. Zienkiewicz O., Taylor R. Finite Element Method: 5 th ed. Vol. 1-3. Butterworth and Heinemann, 2000, 659 p.
18. Park C.Y., Yang D.Y. A study of void crushing in large forgings II. Estimation of bonding efficiency by finite-element analysis. Journal of Materials Processing Technology. 2004, vol. 157-158, pp. 496–501.
19. Duan H., Velay X., Sheppard T. Application of finite element method in the hot extrusion of aluminium alloys. Materials Science and Engineering A. 2004, vol. 369, pp. 66–75.
20. ANSYS. Structural Analysis Guide. Rel. 15.0.
Review
For citations:
Lekhov O.S., Mikhalev A.V. Stress-strain state of metal in deformation zone during production of steel section billets on the unit of combined continuous casting and deformation. Report 2. Izvestiya. Ferrous Metallurgy. 2020;63(9):730-734. (In Russ.) https://doi.org/10.17073/0368-0797-2020-9-730-734
Views:
456
Email this article 