Multivariate estimation of production duration of steel wire batches on the basis of situational-regulatory models. Message 2

Accurate accounting and rating of duration of production cycles is necessary for rational planning and forecasting of production time. Production duration of products batches is the basis for operational schedules design. Without duration of cycles, it is impossible to establish calendar dates for start-up of semi-finished products to a particular stage of processing, as well as to determine timing of production and timing of the products batch for individual production sites. The considered task of multivariate estimation of standard duration of manufacturing of a specific batch of steel wire is to determine optimal duration of operations required for this batch production for each situation. To solve it, it is necessary: to build models of production processes performed in each branch of steelwire complex; to determine composition, duration and conditions for performing technological, natural, labor, control and transport operations; to specify the type and amount of equipment used in each department; to
list types of material flow units (riots, skeins, coils); to establish nature and type of movement of semi-finished products (products) in operations of each process; to specify ways of moving products from each previous peration for each subsequent (piece, batch, batch), as well as the number of packages and lots being moved; to take into account the type of applied production lines (continuous, semi-continuous, discrete). All of the above is reflected in presented multi-loop algorithm, approbation of which is performed by simulation method using field data of operating enterprise.

1. Kulakov S.M., Musatova A.I., Kadykov V.N. Multivariate estima- tion of production duration of steel wire batches on the basis of situational-regulatory models. Message 1. Izvestiya. Ferrous Metal- lurgy. 2019, vol. 62, no. 6, pp. 484–491. (In Russ.).

2. Korytkowski P. Optimization of production capacity in intangible flow production systems. IFAC Proceedings Volumes (IFAC­Papers Online). 2006, vol. 12, part 1, pp. 1–6.

3. Kübler F., Böhner J., Steinhilper R. Resource efficiency optimiza- tion of manufacturing processes using evolutionary computation: A turning case. The 22nd CIRP conference on Life Cycle Engineer- ing. 2015, vol. 29, pp. 822–826.

4. Golubchik E.M., Kuznetsova A.S., Rubin G.Sh. etc. Application of the model and principles of technological adaptation of quality indi- cators in production processes of hardware products. Vestnik MGTU im. G.I. Nosova. 2016, no. 1, pp. 101–108. (In Russ.).

5. Machulin V.M., Sidorchuk V.E., Astratov S.N. etc. Controlling in hardware production at RUE “BMZ”. Lit’e i metallurgiya. 2011, no. 2, pp. 115–123. (In Russ.).

6. Wiśniewski P. Decomposition of business process models into reusable sub-diagrams. ITM Web of Conferences. 2017, vol. 15, no. 01002, pp. 1–8.

7. Foleya J.T., Cochran D.S. Manufacturing system design decompo- sition: an ontology for data analytics and system design evaluation. Procedia CIRP. 2017, vol. 60, pp. 175–180.

8. Rüttimann B. G., Stöckli M. T. Going beyond triviality: the Toyota production system-lean manufacturing beyond muda and kaizen. Jour- nal of Service Science and Management. 2016, no. 9, pp. 140–149.

9. Muhammad Bashir, Ding Liu, Murat Uzam, Naiqi Wu, Abdulrah- man Al-Ahmari, Zhiwu Li. Optimal enforcement of liveness to flexible manufacturing systems modeled with Petri nets via transi- tion-based controllers. Advances in Mechanical Engineering. 2018, vol. 10, no. 1, pp. 1–19.

10. Mikhailova L.V., Paramonov F.I., Chudin A.V. Formirovanie i operativnoe upravlenie proizvodstvennymi sistemami na baze po- tochno­gruppovogo proizvodstva v avtomatizirovannom rezhime [Design and operational management of production systems based on thread-group production in an automated mode]. Мoscow: ITTs MATI, 2002, 60 p. (In Russ.).

11. Mokeeva N.S., Zaev V.A., Sennikova E.V. Ways to reduce duration of production cycle at flexible cutting production. Izv. vuz. Severo­ kavkazskii region. 2008, no. 5, pp. 104–106. (In Russ.).

12. Blagikh I.A., Sal’nikov D.Yu. Management of production cycle of the enterprise (organization). Problemy sovremennoi ekonomiki. 2010, vol. 36, no. 4, pp. 1–7. (In Russ.).

13. Malindžák D. Application of logistic principles in metallurgical production. Metalurgija. 2012, vol. 51, no. 3, pp. 345–348.

14. Julka N., Baines T., Tjahjono B., Lendermann P., Vitanov V. Review of multi-factor capacity expansion models for manufacturing plants: Searching for a holistic decision aid. International Journal of Pro- duction Economics. Special section on organizational structure, cul- ture and operations management: an empirical missing link, April 2007, vol. 106, no. 2, pp. 607–621.

15. Van Dongen B.F., Crooy R.A., Van der Aalst W.M.P. Cycle time prediction: When will this case finally be finished? On the Move to Meaningful Internet Systems 2008: OTM 2008 Confederated Inter- national Conferences (Monterrey, Mexico, November 9­14, 2008). 2008, part I, pp. 319–336.

16. De Bucourt M., Busse R., Güttler F., Wintzer C., Collettini F., Kloe- ters C., Hamm B., Teichgräber U.K. Lean manufacturing and Toyo- ta Production System terminology applied to the procurement of vascular stents in interventional radiology. Insights Imaging. 2011, vol. 4, no. 2, pp. 415–423.

17. Tolmacheva E.A. Predicting the volume of products shipped at in- dustrial enterprises. Gumanitarnye nauchnye issledovaniya. 2016, vol. 57, no. 5, pp. 193–196. (In Russ.).

18. Murav’eva G.Yu. Integrated approach to determining duration of pro- duction cycle in industries with non-piece account of the products. Nauchnye vedomosti. 2016, no. 2 (223), Issue 37, pp. 38–41. (In Russ.).

19. Kulakov S.M., Musatova A.I., Kadykov V.N. Digital prototypes of man-machine system performance (in the case of drawing mills). Iz- vestiya. Ferrous Metallurgy. 2018, vol. 61, no. 6, pp. 485–489. (In Russ.).

20. Kulakov S.M., Musatova A.I., Kadykov V.N. Normative modeling of performance of steel wire coppering unit. Izvestiya. Ferrous Metallurgy. 2018, vol. 61, no. 2, pp. 164–167. (In Russ.).