ON THE CALCULATION OF CONVECTIVE HEAT TRANSFER UNDER MUTUAL-ACTION OF A JET WITH LIMITING SURFACE

The paper proposes a method for calculating convective heat transfer in the interaction of a single circular jet with a flat surface. The differences of the proposed method from the existing ones are given. The concepts “energodynamic potential of the flow” and “energodynamic power of the flow” are introduced, allowing to determine the intensity of convective heat transfer at “gas-solid” boundary. Differences of the proposed definitions from the existing ones are given: heat flux and heat flux density. The principal difference between the heat flux density q and the energy dynamic potential q_э is as follows: the heat flux density q for convective heat transfer problems means the amount of heat that is transferred from a liquid to a solid surface (or vice versa) per unit of time through a unit of heat exchange surface area. Thus, quantity q characterizes the intensity of convective heat transfer process at the interface. The energy dynamic potential q_э characterizes the flow property as a source or carrier of heat. Value of q_э characterizes the specific energy power of the fluid flow. When calculating the heat transfer, it was proposed to divide the jet when interacting with the flat surface into two parts: before the interaction – the jet part, after – the fan flow. The method for calculating convective heat transfer under jet heating, in which the Reynolds criterion calculated by characteristics of the gas at the nozzle exit is decisive, is not entirely correct. It is proposed to use criteria specific to the fan flow. Characteristic values for the fan flow are its initial average velocity U_вп, distance from the critical point of the jet (point of intersection of vertical axis of the jet with the surface) to the current coordinate of radius downstream. To assess the changes in basic characteristics of a free jet at different distances from the nozzle exit to limiting surface, dependences of the following criteria are presented: jet expansion coefficient; jet injection coefficient; velocity coefficient for any jet section; velocity coefficient for any jet section, except h/d₀ = 0; relation of the Reynolds criteria, confirming the need to carry out calculations of heat transfer on the values characteristic separately for the fan flow.

1. Astsaturov V.N., Krasnokutskii P.G. Heat transfer during jet heating of billets. Izvestiya. Ferrous Metallurgy. 1978, no. 1, pp. 56–58. (In Russ.).

2. Astsaturov V.N., Berkovskaya P.S., Krasnokutskii P.G. Investigation of metal heating by attacking jets in the development of multirow furnaces. In: Sb. nauchn. trudov VNIIPITeploproekt: pechi i sushila v mashinostroitel’noi promyshlennosti [VNIIPITeploprect: furnaces and dryers in the engineering industry. Coll. of sci. works of VNIIPIT]. 1978, Issue 45, pp. 3–10. (In Russ.).

3. Vokhmyakov A.M., Kazyaev M.D., Kazyaev D.M. Investigation of convective heat transfer in a through furnace equipped with highspeed burners. Tsvetnye metally. 2011, no. 12, pp. 89–93. (In Russ.).

4. Pribytkov I.A. Energy-saving methods of metal heating based on the use of jets. In: Sb. nauchn. trudov konferentsii: Avtomatizirovannye pechnye agregaty i energosberegayushchie tekhnologii v metallurgii [Coll. of sci. works of the conf.: Automated furnaces and energy-saving technologies in metallurgy]. Moscow: MISiS, 2002, pp. 375–390. (In Russ.).

5. Timoshpol’skii V.I., Trusova I.A., Ratnikov P.E. Possibilities of application of metal jet heating before rolling. Lit’e i metallurgiya. 2007, no. 2, pp. 63–66. (In Russ.).

6. Yudaev B.N., Mikhailov M.S., Savin V.K. Teploobmen pri vzaimodeistvii strui s pregradami [Heat transfer at the interaction of jets with obstacles]. Moscow: Mashinostroenie, 1977, 247 p. (In Russ.).

7. Lisienko V.G., Shleimovich E.M. Improving the thermal characteristics of furnaces and the operating conditions of the lining by improving direct-flame-impingement methods for intensifying the heating of metal. Refractories and Industrial Ceramics. 2013, vol. 54, no. 3, pp. 188–195.

8. Biryukov A.B, Gnitiev P.A. Intensification of convective heat exchange in heating and thermal furnaces. Chernaya metallurgiya. Byul. in-ta “Chermetinformatsiya”. 2017, no. 3, pp. 105–112. (In Russ.).

9. Pribytkov I.A., Titova G.V. Features of jet heating of thermally thin metal. Izvestiya. Ferrous Metallurgy. 1993, no. 9-10, pp. 51–54. (In Russ.).

10. Pribytkov I.A. Calculation of metal thermal state at pulse-speed heating. Izvestiya. Ferrous Metallurgy. 1995, no. 1, pp. 53–56. (In Russ.).

11. Kurnosov V.V., Shul’ts L.A. High temperature nonoxidizing nondecarburizing heating of steel in combined fuel furnaces: problems and decisions. Izvestiya. Ferrous Metallurgy. 2012, no. 11, pp. 10–14. (In Russ.).

12. Astsaturov V.N. Intensification of thermal work of heating furnaces. In: Sb. nauchn. trudov konferentsii: Avtomatizirovannye pechnye agregaty i energosberegayushchie tekhnologii v metallurgii [Coll. of sci. works of the conf.: Automated furnaces and energy-saving technologies in metallurgy]. Moscow: MISiS, 2002, pp. 36–40. (In Russ.).

13. Leprevost J.-C., Lefèvre A., Brancher, J.-P., Saatdjian Estéban. Chao tic mixing and heat transfer in a periodic 2D flow. Comptes Rendus de l’Academie de Sciences. Serie IIb: Mecanique, Physique, Chimie, Astronomie. 1997, vol. 325, pp. 519–526.

14. Crow S.C., Champagne F.H. Orderly structure in jet turbulence. Journal of Fluid Mechanics. 1971, vol. 48, pp. 547–591.

15. Gusovskii V.L., Lifshits A.E. Metodika rascheta nagrevatel’nykh i termicheskikh pechei: Uchebno-spravochnoe izdanie [Method of calculating heating and thermal furnaces: Educational reference book]. Moscow: Teplotekhnik, 2004, 400 p. (In Russ.).

16. Abramovich G.N. Teoriya turbulentnykh strui [Theory of turbulent jet]. Moscow: Nauka, 1984, 716 p. (In Russ.).

17. Michalke A. On spatially growing disturbances in an inviscid shear layer. J. Fluid Mechanics. 1965, vol. 23, Part 3, pp. 521–544.

18. Liepmann D., Gharib M. The role of streamwise vorticity in the nearfield entrainment of round jets. J. Fluid Mechanics. 1992, vol. 245, pp. 643–68.

19. Abramovich G.N. Prikladnaya gazovaya dinamika. T. 1: Ucheb rukovodstvo dlya vtuzov [Applied gas dynamics. Vol. 1: Tutorial manual for technical universities]. Moscow: Nauka, 1991, 600 p. (In Russ.).

20. Krivandin V.A., Arutyunov V.A, Belousov V.V. Teplotekhnika metallurgicheskogo proizvodstva [Heat engineering of metallurgical production]. Vol. 1. Moscow: MISIS, 2001, 608 p. (In Russ.).