CALCULATION OF PARAMETERS OF RESILIENT PNEUMATIC ELEMENT, EXECUTED AS A CYLINDER WITH LIMITED RADIAL DEFORMATION
https://doi.org/10.17073/0368-0797-2018-8-620-624
Abstract
The reasons for the occurrence of vibrations in engineering constructions and their effect on the operability of mechanisms are considered It is determined that one of the main sources of vibration of machine elements are plain bearings, in which the shaft is located in the hollow bar (liver) with a gap, there is a struck at the selection of it. The principle of vibration protection systems is considered, the main element of which is the elastic element - shock absorber. The influence of the rigidity of the elastic element on the performance of sliding bearings is analyzed. The design of an elastic pneumatic element of increased stiffness, made in the form of a cylinder with limited radial deformation, is given. It is shown that the ability of such an element to center the shaft relative to the geometric axis of the support under the action of a radial load is provided by the appearance of a difference in contact area between the outer surface of the bearing housing and the surface of the elastic cylinder. A technique is developed for calculating the increment of the contact area of an elastic element, made in the form of a pneumatic cylinder with limited radial deformation, with a surface through which the external load is transmitted at specified support parameters: the length of the cylinder and the amount of excess gas pressure inside the cylinder. It is believed that the shaft is in the bearing without a gap, and the shell forming the cylinder is inextensible. It is established that the deformation and rigidity of an elastic pneumatic cylinder with limited radial deformation depend on its length and the magnitude of the excess pressure inside the cavity. The obtained mathematical dependencies allow defining and setting parameters of an elastic pneumatic element made in the form of a cylinder with limited radial deformation (cylinder length and the value of excess gas pressure inside the cylinder) depending on operating conditions of the sliding bearing.
Keywords
About the Authors
A. G. Nikitin
Siberian State Industrial University
Russian Federation
Russian Federation
Postgraduate of the Chair of Mechanics and Machine Engineering
Novokuznetsk, Kemerovo Region, Russia
A. V. Abramov
Siberian State Industrial University
Russian Federation
Russian Federation
Postgraduate of the Chair of Mechanics and Machine Engineering
Novokuznetsk, Kemerovo Region, Russia
J. A. Bazhenov
Ural Federal University named after the first President of Russia B.N. Yeltsin
Russian Federation
Russian Federation
Cand. Sci. (Eng.), Assist. Professor of the Chair of Marketing
Ekaterinburg, Russia
References
1. Ivanov A.P. Dinamika sistem s mekhanicheskimi soudareniyami [Dynamics of the systems with mechanical collisions]. Moscow: Mezhdunarodnaya programma obrazovaniya, 1997, 336 p. (In Russ.).
2. Brach R.M. Moments between impacting rigid bodies. Trans. ASME, I. Mech. Design. 1981, vol. 103, no. 4, pp. 812–817.
3. Budd C., Dux F., Cliffe A. The effect of frequency and clearance variations on single-degree-of-freedom impact oscillator. J. Sound and vibrations. 1995, vol. 184, no. 3, pp. 475–502.
4. Earles S.W.E., Wu C.L.S. Motion analysis of a rigid-link mechanism with clearance at a bearing using Lagrangian mechanics and digital computation. In: Mechanism 1972, Institution of Mechanical Engineers. London, England, 1973, pp. 83–89.
5. Haines R.S. A theory of contact loss at revolute joints with clearance. Journal of Mechanical Engineering Science. 1980, vol. 22, no. 3, pp. 129–136.
6. Hogan S. On the dynamics of rigid-block motion under harmonic forcing. Proc. Roy. Soc. London. 1989, vol. 425A, no. 1869, pp. 441–479.
7. Perera O., Seering W.F. Prevention of impact in bearings of four-bar linkages. ASME Journal of Mechanisms, Transmissions and Automation in Design. 1983, vol. 105, no. 3, pp. 592–598.
8. Shaw S.W., Holmes P.J. A periodically forced impact oscillator with large dissipation. ASME, J. Of appl. Mech. 1983, vol. 50, pp. 849–857.
9. Aref’ev V.A., Il’ichev I.I., Kashevskaya L.A. etc. Selection of parameters of effective vibration isolation of elastic support of the gear drive. Vestnik mashinostroeniya. 1980, no. 8, pp. 17–19. (In Russ.).
10. Dubowsky S., Moening M.F. An experimental and analytical study of impact forces in elastic mechanical systems with clearances. Machine and Mechanisms Theory. 1978, vol. 13, pp. 451–465.
11. Eubanks R.A. Investigation of a rational approach to shock isolator design. Shock and Vibration Bulletin. 1964, vol. 34, no. 3, pp. 137–167.
12. Lowen G.G., Jandresists W.G. Survey of investigations into the dynamic behavior of mechanisms containing links with distributed mass and elasticity. Mechanism and Machine Theory. 1972, vol. 7, pp. 3–17.
13. Moening M.F. An experimental and analytical study of elastic mechanical systems with clearances. MS thesis, School of Engineering and Applied Science. University of California, Los Angeles, Calif., 1976.
14. Sevin E., Pilkey W. Optimum shock and vibration isolation systems, SVM-6. The Shock and Vibration Information Center, 1971.
15. Kosarev O.I. Active damping of secondary field of the cylindrical shell in far zone using the driving forces applied to the shell. Problemy mashinostroeniya i nadezhnosti mashin. 2013, no. 1, pp. 10–17. (In Russ.).
16. Karaban V.V., Kartsev S.K., Safronov Yu.G., Sinev A.V. Optimization of eigen-frequency spectrum of the solid suspension by varying the geometric and stiffness parameters. Problemy mashinostroeniya i nadezhnosti mashin. 1993, no. 2, pp. 20–25. (In Russ.).
17. Nikitin A.G. Determination of internal parameters of the support with an elastic pneumatic element. Vestnik mashinostroeniya. 1999, no. 4, pp. 15–17. (In Russ.).
18. Nikitin A.G., Vekesser A.Yu., Sakharov D.F. Calculation of the stiffness of a pneumatic toroid with reduced tangential deformation. Izvestiya VUZov. Chernaya metallurgiya = Izvestiya. Ferrous Metallurgy. 2009, no. 8, pp. 64–66. (In Russ.).
19. Nikitin A.G., Chainikov K.A. Deformation of elastic cylindrical element in pneumatic shock absorber. Russian Engineering Research. 2011, vol.31, no. 8, pp. 742–743.
20. Nikitin A.G., Chainikov K.A., Degtyar’ V.A., Zhivago E.Ya. Calculation of pneumatic cylinder rigidity with limited axial deformation. Izvestiya VUZov. Chernaya metallurgiya = Izvestiya. Ferrous Metallurgy. 2012, no. 4, pp. 68–70. (In Russ.).
21.
22.
23.
Review
For citations:
Nikitin A.G., Abramov A.V., Bazhenov J.A. CALCULATION OF PARAMETERS OF RESILIENT PNEUMATIC ELEMENT, EXECUTED AS A CYLINDER WITH LIMITED RADIAL DEFORMATION. Izvestiya. Ferrous Metallurgy. 2018;61(8):620-624. (In Russ.) https://doi.org/10.17073/0368-0797-2018-8-620-624
Views:
381
Email this article 