INFLUENCE OF VARIABLE FRICTION FORCES ON SIZES OF SLIP, RETARDATION AND DEAD ZONES IN UPSETTING PROCESS
https://doi.org/10.17073/0368-0797-2017-9-691-697
Abstract
The analyses of new solutions to determine the contact stress in zones with variable frictional forces for upsetting the rectangular strip were executed. It is shown that replacement of the Mises precise plasticity condition by an approximate condition in terms of primary stress changes the character of curves contact stresses in the slip and dead zones, and significantly influences on the dimensions of these zones. It was established that with the decrease of the friction force at the boundary of the dead zone its width increases. As a result of numerical analysis of the stress state at the dead zone dependence of its width from the value of contact shear stresses on the boundary of dead zone was proposed. Conditions of existence and sizes of the slip, retardation and dead zones on the contact surface of the deformation region were installed in dependence on friction coefficient and relative width of the strip. Considering distributions of the contact stresses, expressions to determine the efforts of the upsetting process were found. The results were compared with known experimental and theoretical data. The estimation of error calculation effort of upsetting was obtained by the engineering methods.
About the Author
G. I. Baranov
Ural Federal University named after the first President of Russia B.N. Yeltsin.
Russian Federation
Russian Federation
Dr. Sci. (Eng.), Professor of the Chair “Machinery Parts”.
Ekaterinburg.
References
1. Levanov A.N., Kolmogorov V.L., Burkin S.P. etc. Kontaktnoe trenie v protsessakh obrabotki metallov davleniem [Contact friction in metal forming processes]. Moscow: Metallurgiya, 1976, 416 p. (In Russ.).
2. Grudev A.P., Zil’berg Yu.V., Tilik V.T. Trenie i smazki pri obrabotke metallov davleniem [Friction and lubrication in metal forming]. Moscow: Metallurgiya, 1982, 312 p. (In Russ.).
3. Unksov E.P. Inzhenernaya teoriya plastichnosti [Engineering theory of plasticity]. Moscow: Mashgiz, 1959, 328 p. (In Russ.).
4. Grudev A.P. Teoriya prokatki [Rolling theory]. Moscow: Intermet Inzhiniring, 2001, 280 p. (In Russ.).
5. Nikitin G.S. Teoriya nepreryvnoi prodol’noi prokatki [Theory of continuous longitudinal rolling]. Moscow: Izd-vo MGTU im. N.E. Baumana. 2009, 399 p. (In Russ.).
6. Storozhev M.V., Popov E.A. Teoriya obrabotki metallov davleniem [Theory of metal forming processes]. Moscow: Mashinostroenie, 1977, 424 p. (In Russ.).
7. Unksov E.P., Johnson W., Kolmogorov V.L. etc. Teoriya plasticheskikh deformatsii metallov [Theory of the plastic deformation of metals]. Moscow: Mashinostroenie, 1983, 598 p. (In Russ.).
8. Sokolovskii V.V. Teoriya plastichnosti [Theory of plasticity]. Moscow: Vysshaya shkola, 1969, 608 p. (In Russ.).
9. Malinin N.N. Tekhnologicheskie zadachi plastichnosti i polzuchesti [Technological problems of plasticity and creep]. Moscow: Vysshaya shkola, 1979, 119 p. (In Russ.).
10. Tret’yakov E.M. Elastic and plastic deformations of thin strips under their compression between plane rigid stamps. Vestnik MGTU im. N.E. Baumana. Ser. Mashinostroenie. 2015, no. 3, pp. 103–118. (In Russ.).
11. Smirnov V.S. Teoriya obrabotki metallov davleniem [Theory of metal forming]. Moscow: Metallurgiya, 1973, 496 p. (In Russ.).
12. Vorontsov A.L. Solution of the plane problem of the theory of plasticity in metal forming processes analysis. Part 2. Stress and kinematic states at upsetting the rectangular strip with friction. Kuznechno-shtampovochnoe proizvodstvo. Obrabotka materialov davleniem. 2012, no. 7, pp. 3–15. (In Russ.).
13. Garber E. A., Kozhevnikova I. A., Tarasov P. A. Calculating the hotrolling forces for thin strip, with allowance for the stress–strain state in adhesion zone of deformation region. Prokatnoe proizvodstvo. 2007, no. 4, pp. 7–14. (In Russ.).
14. Baranov G.L. Analysis of the contact stresses in the zone of plastic deformation with sign-variable friction forces. Izvestiya VUZov. Chernaya metallurgiya = Izvestiya. Ferrous Metallurgy. 2015, vol. 58, no. 3, pp. 192–195. (In Russ.).
15. Baranov G.L. Determination of contact stresses when upsetting a rectangular strip. Izvestiya VUZov. Tsvetnaya metallurgiya. 2015, no. 4, pp. 25–31. (In Russ.).
16. Baranov G.L. Improvement of calculation methods for stresses in tasks of flat plastic deformation. Kuznechno-shtampovochnoe proiz vodstvo. Obrabotka materialov davleniem. 2015, no. 3, pp. 3–9. (In Russ.).
17. Baranov G.L. Improved calculation of the contact stress in strip rolling. Steel in Translation. 2015, vol. 45, no. 6, pp. 447–452.
18. Konovalov Yu.V. Spravochnik prokatchika. Kniga 1. Proizvodstvo goryachekatanykh listov i polos [Reference book of rollerman. Book 1. Production of hot-rolled sheets and strips]. Moscow: Teplotekhnik, 2008, 640 p. (In Russ.).
19. Nikolaev V.A. Effort calculation at hot rolling. Izvestiya VUZov. Chernaya metallurgiya = Izvestiya. Ferrous Metallurgy. 2005, no. 1, pp. 24–29. (In Russ.).
20. Brovman M.Ya. Primenenie teorii plastichnosti v prokatke [Application of the theory of plasticity in rolling]. Moscow: Metallurgiya, 1991, 254 p. (In Russ.).
Review
For citations:
Baranov G.I. INFLUENCE OF VARIABLE FRICTION FORCES ON SIZES OF SLIP, RETARDATION AND DEAD ZONES IN UPSETTING PROCESS. Izvestiya. Ferrous Metallurgy. 2017;60(9):691-697. (In Russ.) https://doi.org/10.17073/0368-0797-2017-9-691-697
Views:
672
Email this article 