IMPROVEMENT OF THE PRODUCTION EFFICIENCY OF REINFORCEMENT SECTIONS AT THE OPERATING CONTINUOUS SMALL-SECTION MILL

The article considers a promising combined method for increasing the production effi ciency of the section rolling profi les – rollingdivision with the use of non-powered dividing tool, the experience in the use of which in the conditions of production has shown high effi - ciency of this direction in terms of reducing the cost of the fi nished product. The dependences, which allow to defi ne the frequency separation, and high-speed conditions when deciding industrial introduction of process technology of rolling-separation on current continuous small-section mill 250. The existing experience of implementing the rolling process-separation model of continuous small-grade mill 250 has been reviewed, which allowed to reveal the peculiarities in the distribution coeffi cients of drawing and changing speed conditions for groups of stands. It was found that on the basis of capacity of rolling equipment on the mill, it is advisable to carry out the longitudinal separation of the workpiece into two bands in the fi nishing group of stands, and changes in the total coeffi cients of drawing and rolling speed on rolling groups were also identifi ed. The article presents data on changes in the machine time for reinforcing the profi le no. 10, no. 12, no. 14 in connection with the development of technology in the process of rolling-division, which in turn contributed to increasing eff ectivelySTI production of existing continuous small-section mill. Proven in the industry values of the total coeffi cients of drawing and rolling speed on rolling groups can be determined from the shown illustrations. In addition, the study process was carried out for experimental – industrial rolling of rebar no. 8 under conditions of continuous light section mill 250-1 of the rolling shop of JSC “EVRAZ ZSMK”. The authors have compared the coeffi cients of drawing and rolling speed in the production of rebar no. 8 on the continuous wire mill 250 and a continuous small-section mill 250 from the same piece – square 100 mm. The results are provided in the illustration, which shows that the use of the rolling process-separation allows to use four stands less than at the rod mill at production of rebar no. 8 at a small-section mill.

1. Zhuchkov S.M. Use of idler work rolls in two-high rolling with longitudinal stock slitting in mill line. Steel in Translation. 1997, vol. 27, no. 7, pp. 28–33.

2. Efimov O.Yu., Chinokalov V.Ya., Fastykovskii A.R., Kopylov I.V. Introduction of a splitting operation in rolling on a continuous small-bar mill. Steel in Translation. 2008, vol. 36, no. 4, pp. 327–328.

3. Zhuchkov S.M. Particularities in technological scheme for process of three-strand rolling-slitting at 320/150 wire-rod mill. Metallurgist. 2001, no. 1, pp. 46–47. (In Russ.).

4. Zhuchkov S.M., Bondarenko A.M., Asapov V.N., Dyshlevich V.F. Improvement of split rolling of rebar at 320/150 mm mill. Stal’. 1994, no. 2, pp. 48–51. (In Russ.).

5. Zhuchkov S.M., Filippov V.V., Tishchenko V.A., Bondarenko A.N. Trends in development of technology for rolling-slitting. Stal’. 2001, no. 10, pp. 33–35. (In Russ.).

6. Zhuchkov S.M. Use of the reserve of retracting frictional forces. Lit’e i metallurgiya. 2002, no. 4, pp. 166–174.(In Russ.).

7. Khokhlov S.A., Perunov G.P., InatovichYu.V. etc. Development and introduction of optimal technological modes of rolling on the small-section wire mill 320/150 of JSC “Amurmetall”. Proizvodstvo prokata. 2009, no. 11, pp. 14–17. (In Russ.).

8. Perunov G.P., Khokhlov S.A., Smirnov V.K. etc. Optimization of the technological modes of rolling-separation on the mill 320/150 of JSC “Amurmetall”. Proizvodstvo prokata. 2008, no. 9, pp. 20–24. (In Russ.).

9. Luduga L., Kolodziej K. Kalibrovanie i technologia walcowania ksztaltownikow paduwojnych z rozeinaniem nagoraco. Przegląd Institutu metallurgii Żelazo. 1977, vol. 29, no. 1, pp. 17–24. (In Polish).

10. Palmer L.W. Slit-rolling technology. World Steel & Metalworking. 1984, 1985, vol. 6, pp. 147–149.

11. Slednev V.P. Sparennaya prokatka sortovykh profi lei [Twin rolling of profi led sections]. Moscow: Metallurgiya, 1988, 167 p. (In Russ.).

12. Sato R. The rolling of products using slit – rolling process. NKK report. 1980, no. 3, pp. 42–46.

13. Matsuo G., Suzuki M. The latest technology of multi – slit rolling. SEAISI Quaterly. 1995, no. 3, pp. 49–58.

14. KlimenkoV.M. Mnogoruch’evaya prokatka-razdelenie [Multi-strand rolling-separation]. Moscow: Metallurgiya, 1982, 167 p. (In Russ.).

15. Efimov O.Y., Fastykovskii A.R., Chinokalov V.Y., Kopylov I.V. Introduction of a splitting operation in rolling on a continuous small-bar mill. Steel in Translation. 208, vol. 38, no. 4, pp. 327–328.

16. Efimov O.Yu., Chinokalov V.Ya., Fastykovskii A.R., Kopylov I.V., Makhrin A.N. Employing rolling and separation technology in the 250-1 mill. Steel in Translation. 2008, vol. 38, no. 8, pp. 671–673.

17. Fastykovskii A.R., Peretyat’ko V.N., Fastykovskii D.A. Aspects of the lengthwise cutting of rolled sections by undriven rotary shears in the mill line. Metallurgist. 2003, vol. 47, no. 3-4, pp. 120–124.

18. Fastykovskii A.R., Efi mov O.Yu., Chinokalov V.Ya. Experience in using rolling-separation technology to improve the competitiveness of rolling products. In: Mezhdunarodnaya nauchno-prakticheskaya konferentsiya. Strategiya antikrizisnogo upravleniya ekonomicheskim razvitiem rossiiskoi federatsii [International Sci.-Practical Conf. Strategy of anti-crisis management of the economic development of the Russian Federation]. Penza: PGU, 2009, pp. 131–133. (In Russ.).

19. Perunov G.P., Limankin V.V., Volkov K.V. Mastering the technology of rolling-separating of reinforcing steel on a small-section wire mill 320/150 of JSC “Amurmetall”. Proizvodstvo prokata. 2006, no. 10, pp. 16–19. (In Russ.).

20. Perunov G.P., Khokhlov S.A., Volkov K.V. etc. Introduction of rolling-separation technology for reinforcing bars on the mill 320/150. Stal’. 2010, no. 5, pp. 90–92. (In Russ.).