EXPERIMENTAL RESEARCH PHOTOGRAMMETRY METHOD FOR THE FORMING OF PIPE BILLET ON THE EDGE-BENDING PRESS SECTOR OF THE LINE TESA 1420
https://doi.org/10.17073/0368-0797-2014-5-15-18
Abstract
The results of experimental studies are shown using new measurement techniques for non-contact measurements of geometric billets on edge-bending press sector of the line 1420. The estimation of the influence of geometry on the edge of the pipe blank form to the marginal zone after subsequent processes is described. The article lists he steps of the pilot study. The experimental data is shown as coordinate points. A comparative analysis of the results of measurements of edges geometry was made in various ways. The advantages and a perspective of photogrammetry are described for the production of large diameter pipes.
About the Authors
S. V. Samusev
National University of Science and Technology “MISIS” (MISIS) (Moscow, Russia)
Russian Federation
Dr. Eng., Professor
Russian Federation
Dr. Eng., Professor
M. A. M.A. Tovmasyan
National University of Science and Technology “MISIS” (MISIS) (Moscow, Russia)
OJSC “Vyksa metallurgical plant” (Vyksa, Nignij Novgorod region, Russia)
Russian Federation
Postgraduate, Specialist of the Department of mathematical modeling
Russian Federation
Postgraduate, Specialist of the Department of mathematical modeling
O. S. Hlybov
OJSC “Vyksa metallurgical plant” (Vyksa, Nignij Novgorod region, Russia)
Russian Federation
Russian Federation
Cand. Eng., Head of the Department of mathematical modeling
L. V. Drozdov
OJSC “Vyksa metallurgical plant” (Vyksa, Nignij Novgorod region, Russia)
Russian Federation
Senior Division calibrator of pipes with large diameter
Russian Federation
Senior Division calibrator of pipes with large diameter
D. E. Kerentsev
OJSC “Vyksa metallurgical plant” (Vyksa, Nignij Novgorod region, Russia)
Russian Federation
Chief Specialist of the Department of mathematical modeling
Russian Federation
Chief Specialist of the Department of mathematical modeling
References
1. Samusev S.V., Romancov A.I., Zhigunov K.L. etc. Izv. VUZov. Chernaja metallurgija. 2012. № 1. Pp. 26 – 29.
2. Jai Dev Chandel, Nand Lal Singh. Engineering (In-dia). 2011. № 3. Pp. 400 – 410.
3. Samusev S.V., Romancov A.I., Zhigunov K.L. etc. Proizvodstvo prokata. 2011. № 10. Pp. 20 – 28.
4. FAN Lifeng, GAO Ying, LI Qiang. Chinese journal of mechanical engineering. 2012. № 4. Pp. 256-265.
5. Samusev S.V., Ljuskin A.V., Romancov A.I. etc. Izv. VUZov. Chernaja metallurgija. 2013. № 3. Pp. 20 – 22.
6. Samusev S.V., Tovmasjan M.A., Hlybov O.S., Droz-dov L.V. Proizvodstvo prokata. 2014. № 2. Pp. 40 – 42.
7.
Review
For citations:
Samusev S.V., M.A. Tovmasyan M.A., Hlybov O.S., Drozdov L.V., Kerentsev D.E. EXPERIMENTAL RESEARCH PHOTOGRAMMETRY METHOD FOR THE FORMING OF PIPE BILLET ON THE EDGE-BENDING PRESS SECTOR OF THE LINE TESA 1420. Izvestiya. Ferrous Metallurgy. 2014;57(5):15-18. (In Russ.) https://doi.org/10.17073/0368-0797-2014-5-15-18
Views:
701
Email this article 